Never use this product in a device for personnel protection.
In case of using devices for personnel protection, use products which meet
laws and standards, such as OSHA, ANSI or IEC etc., for personnel protec-
tion applicable in each region or country.
PART DESCRIPTION
1
one-side reverse direction, a direction opposite to the forward direction display will be the
Flow direction set-
ting
PRO MODE
.”
2) ø4 push-in joint / ø8 push-in joint is incorporated into
FM-
!
-4
(
-P
) /
FM-
!
-8
(
-P
), respec-
tively. The push-in joint is not incorporated into the aluminum body type.
MODE key
Forward direction display
(Note 1)
UP key
DOWN key
Connector area
for piping
(Note 2)
Connector area
for piping
(Note 2)
Comparative output 2 indicator (Green)
Comparative output 1 indicator (Green)
Main display
(Green / Red)
Sub display (Green / Red)
Connector area for
cable with connector
PIPING
2
" ## $% & &# & $& ' *$
product.
Before using the product,
make sure to check that
& %+#*
Material of tube Tube diameter
Allowable diameter
Polyamid
ø4, ø8
Within ±0.1mm
Polyurethane
ø4
Within ±0.1mm
ø8
0.1 / -0.15mm
6## %# * # + %# 7+# $+*
side (upstream) of the product since the compressed air from the compressor
contains drain (water, oil oxide and foreign materials, etc.). Mesh (wire net) in the
$& & * $$ 9#* ## %# $+*
$& + %# +: +#
Pneumatics
pressure
source
Filter
Regulator
Flow sensor
(This product)
Air dryer
Oil mist filter
(Micro-alescer)
& :#: $+* $& #* & #$ $%-
tion valve. The product may malfunction or break if subject to splattering grease or oil, etc.
& $& $ :% #* ##
%# %# $$* ;<+ # & $:
& +# &+ +$
dew point and ambient temperature of the product, use the product under the
conditions that dew condensations will not be formed in the inside of pipe.
In case of mounting commercial joint to the aluminum body type, apply a spanner on
the metal part of this product and tighten by the tightening torque of 16 to 18N·m.
If excessive torque is applied, the commercial joint or the main body may break.
When piping, care must be taken that foreign materials such as sealing tape
and adhesive must not enter into the inside. If the foreign materials are en-
tered, the product may malfunction or break.
Make sure to mount the joint when using the product with its secondary side (downstream)
$ 6 ' +& $ %# $& +* ##
MOUNTING
4
Horizontal mounting
Use M3 screw and the tightening torque should be 0.5N·m.
<Resin body type>
Vertical mounting
Use M3 screw and the tightening torque should be 0.5N·m.
<Resin body type>
<Aluminum body type>
When using sensor mounting bracket
When mounting the product on the sensor mounting bracket
MS-FM2-1
(op-
tional) or
MS-FM2-2
(optional), use the M3 screw (length 6mm) attached to
the sensor mounting bracket. The tightening torque should be 0.5N·m.
Use M3 screw to mount the sensor mounting bracket on a sensing surface.
<Resin body type>
<Aluminum body type>
Use
MS-FM2-1
Use
MS-FM2-2
27
17mm
2-ø3.4
through-hole
(Unit: mm)
Dimension
M3 screw
(Please arrange separately.)
15.5
9.5
2-M3
depth 5
M3 screw
(Please arrange separately.)
(Unit: mm)
Dimension
30
13
2-M3 depth 5
M3 screw
(Please arrange separately.)
(Unit: mm)
Dimension
30
6
3.5
(Unit: mm)
Dimension
M3 screw
(Please arrange separately.)
M3 screw (length 6mm)
(Attached to
MS-FM2-1
)
30
40
6
3.5
(Unit: mm)
Dimension
M3 screw
(Please arrange separately.)
M3 screw (length 6mm)
(Attached to
MS-FM2-2
)
I/O CIRCUIT DIAGRAMS
5
NPN output type
PNP output type
Internal circuit
Users’ circuit
(Brown) +V
Load
Load
(White) CH2 (Comparative output 2 / External input)
(Blue) 0V
(Note)
(Note 2)
9$$K QX
(*1)
(*2)
(Black) CH1
(Comparative output 1)
50mA max.
50mA max.
(Gray) Analogue voltage output
+
-
12 to 24V DC
±10%
Terminal No.
Color code of cable with connector
Main circuit
Internal circuit
Users’ circuit
Color code of cable with connector
(Brown) +V
Load
Load
(White) CH2 (Comparative output 2 /
External input)
(Blue) 0V
(Note)
(*1)
(*3)
(Black) CH1
(Comparative output 1)
50mA
max.
50mA max.
(Gray) Analogue voltage output
+
-
12 to 24V DC
±10%
Terminal No.
Main circuit
(Note 2)
9$$K QX
*2: When using CH2 as an external input
Non-voltage contact, NPN transistor or
DC 2-wire output
or
High (+5 to +V or Open): Invalid
Low (0 to +0.4V): Valid
*3: When using CH2 as an external input
Non-voltage contact, PNP transistor or
DC 2-wire output
or
High (+5 to +V): Valid
Low (0 to +0.6V or Open): Invalid
*1: When using CH2 as a comparative output 2
Notes: 1) As for the aluminum body type, variable resistor (clamping voltage: approx. 40V) is con-
nected between the internal power circuit and the metal body to prevent breakdown of the
[ +# * \] $ &$$#* + & 7^ :
that is connected to 0V. High potential and insulation resistance tests between the internal
power circuit and the metal body must not be done.
2) Short-circuit protection is not incorporated into the analogue voltage output.
Do not connect the power supply or capacitive load directly to the analogue voltage output.
<Terminal arrangement> (Sensor body)
Terminal
No.
Color code of the
cable with connector
Terminal name
1
Brown
+V
2
Black
CH1 (comparative output 1)
3
White
CH2 (comparative output 2 / external input)
4
^*
Analogue voltage output
5
Blue
0V
1 2 3 4 5
WIRING
3
Connector
cover
Connection method
Insert the cable with connector
CN-F15-C1
(accessory) into the
connector area of this product and mount the connector cover.
Disconnection method
Remove the connector cover and pressing the release lever of the cable with
connector, pull out the connector.
Note: Do not pull by holding the cable without pressing the release lever, as this can cause cable
break or connector break.
OUTPUT MODE
6
" &$& _ + +$ + * + -
grated output mode or integrated pulse output mode can be selected as the
output mode for comparative output 1 and comparative output 2.
`
Output mode and threshold value setting mode
MENU
SETTING MODE
” for details.
INSTRUCTION MANUAL
6 6 "*$ ^ # z
FM-200
Series
{|{};; ;;~}]
Thank you very much for purchasing Panasonic products.
Please read this Instruction Manual carefully and thoroughly for the correct and
optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
D2-255025-A
Ramco National
800-280-6933 | [email protected]
www.panasonicsensors.com
