Panasonic EBL128 Planning Instructions Download Page 41 | Manualshive

Page: 41 / 179

Panasonic EBL128 Planning Instructions Download Page 41

Panasonic Eco Solutions Nordic AB

MEW01622

Rev: -

EBL128 Planning Instructions V2.0.x

39

programmed technical address is to be written.

The Address setting tool is also used for mode setting:

NORMAL mode

: 4300 in this mode is in EBLWin, for the

smoke detector, set to one of six alarm algorithms H-15, H-35,
L-15, L-35,

N-15

or N-35 and for the heat detector set to one of

three alarm algorithms for class

A1

(static response temp. 54-

65°C), A2 S (54-70°C) or B S (69-85°C).

2330 mode

: 4300 in this mode (+ base 3312) works like the

ionization smoke detectors 2316 / 2317 (+ base 2330).

2312 mode

: Not used in EBL128.

4400

Analog  multi  detector.    Replaces  4300,  see  above.    4400  is  a
smoke  detector  and  a  heat  detector  in  one  housing.    Scattered
light  (i.e.  reflection  of  infrared  light)  is  used  to  detect

smoke

and the

heat

sensing element is a thermistor. The detector has

unleaded soldering.

Shall be plugged in an analog base 3312xx/3379/4313. Built-in
LEDs (red) are blinking to indicate that the detector

40

has

activated  a  fire  alarm.    Prepared  for  mechanical  lock  (screw
attached) – if required.   4400 has a little different design than
the 4300 detector and the smoke chamber net has even smaller
holes  that  will  keep  insects  and  particles

41

larger than smoke

particles out of the chamber.

The COM loop address (Technical address) is set with the
Address setting tool 3314 /

4414

. The detector has an address

label on which the programmed technical address can be
written.

The Address setting tool is also used for

mode setting

:

Advanced mode

: 4400 has to be set to Advanced mode via the

Address setting tool

4414

.

Note, the Address setting tool 3314

cannot be used to set Advanced mode!

In Advanced mode this

detector will use algorithms in the detector for fire alarm
evaluation. It can be set to a Learning function

or

via EBLWin

to  one  of  five  area  alarm  algorithms  (Normal,  Clean,
Smoke/Steam,  Cooking/Welding  or  Heater  area),  see  chapter
"Advanced  mode",  page  123.    An  alternative  area  alarm
algorithm  can  be  used  via  a  time  channel.    4400  has  a  green
polling LED.  Via EBLWin is set if the green polling LED shall
blink when the detector is polled or never blink.  Note, the LED
will not be blinking if the detector is in Test mode.
In  Advanced  mode  only  one  COM  loop  address  will  be
occupied for the multi detector.

NORMAL mode

: 4400 in this mode has to be programmed in

EBLWin as a

4300

detector, i.e. the 4400 detector will work as

and replace the Analog multi detector 4300 (see 4300 above)
and two COM loop addresses will be occupied, see 4300 above.

40

I.e. the heat detector and/or the smoke detektor.

41

For example dust, steam, etc.

«
...
39
40
41
42
43
...
»

Summary of Contents for EBL128




















































































































































































Reviews:

No comments