49
39
E
N
G
L
I
S
H
40
E
N
G
L
I
S
H
48
CQ-VA7800N
CQ-VA7800N
Installation
For Installation
For Wiring
Preparation
Dashboard Installation
Supplied Hardware
Cautions:
¡
¡
Please follow the laws and regulations of your
province or country for installation of the unit.
¡
¡
When bending the mounting tab of the mounting
collar with a screwdriver, be careful not to injure
your hands and fingers.
¡
¡
We strongly recommend you to wear gloves for
installation work to protect yourself from injuries.
Caution:
Do not disconnect the battery terminals of a
car with trip or navigational computer since all user set-
tings stored in memory will be lost. Instead take extra
care with installing the unit to prevent shorts.
¡
Before installation, check the radio operation with anten-
na and speakers.
¡
Disconnect the cable from the negative (–) battery termi-
nal (see caution below).
¡
The unit should be installed in a horizontal position with
the front end up at a convenient angle, but not more than
30°.
Installation Opening
The unit can be installed in any dashboard having an open-
ing as shown at right. The dashboard should be 4.5 mm - 6
mm thick in order to be able to support the unit.
Installation Precautions
This product should be installed by a professional
installer.
In case of difficulty, please contact the shop where you
purchased this product.
1. This system is to be used only in a 12-volt, DC battery
system (car) with negative ground.
2. Follow the electrical connections carefully (
a
page 56-
66). Failure to do so may result in damage to the unit.
3. Connect the power lead after all other connections are
made.
4. Be sure to connect the battery lead (yellow) to the posi-
tive terminal (+) of the battery or fuse block (BAT) termi-
nal.
5. Insulate all exposed wires to prevent short circuiting.
6. Secure all loose wires after installing the unit.
7. Please carefully read the operating and installation
instructions of the respective equipment before connect-
ing it to this unit.
30° or less
182 mm
53 mm
Transportation bracket
removal
Be sure to remove the transportation brackets
before use (installation).
Use binding-head screws (5
mm
ø
x 6 mm) for
installation. (
a
page 52)
Be careful not to lose these screws.
Binding-Head Screws
(5
mm
ø
x 6 mm)
Binding-Head Screws
(5
mm
ø
x 6 mm)
Transportation
Bracket
Transportation
Bracket
Q’ty
Diagram
Item
1
Power Connector
1
Reverse Extension Cord
(for rear view camera)
1
Clip Connector
1
Display Unit/Hide-away Unit
Connecting Cord
1
ISO Antenna Adapter
No.
@0
@1
@2
@3
@4
Q’ty
4
Diagram
Item
No.
Tapping Screw
(6
mm
ø
x 20 mm)
!1
4
Hex. Nut (5
mm
ø
)
(for mounting bracket)
!2
2
Mounting Bracket
!3
2
Base Bracket
!4
2
Double-Faced Adhesive Tape
(for hide-away unit)
!5
2
Velcro Tape
!6
1
Tapping Screw (5
mm
ø
x 16
mm) (for rear of the unit)
!7
1
Hex. Nut (5
mm
ø)
(for rear of the unit)
!8
1
Rear Support Strap
!9
Q’ty
1
Diagram
Item
No.
Trim Plate
q
1
Mounting Collar
w
2
Mounting Spring
e
1
Mounting Bolt (5
mm
ø
)
r
2
Binding-Head Screw
(5
mm
ø
x 6 mm)
t
4
Flat-Head Screw
(5
mm
ø
x 6 mm)
y
4
Binding-Head Screw
(4
mm
ø
x 3 mm)
u
2
Spacer
i
1 set
Double-Faced Adhesive Tape
(for spacer)
o
4
Binding-Head Screw
(5
mm
ø
x 8 mm)
!0
