– 160 –
Chapter 7 Output and Screen Display — Screen status display
Screen status display
Screen display during shooting
TCG 1 2 : 3 4 : 5 6 : 2 8
2160-59.94p
MOV 420 150M
A001C001
A 3200K
IP REMOTE
36dB
ND:CLR
1/10000
F5.6+50
H.SENS.
DEC 3 1 2 0 1 9 1 0 : 4 5 : 3 0
iZ123
MF99
D2x
IR
70%
S/H
INTRVL
ND1/16
FLUO.
999min
999min
S.SLOW120
FBC
RELAY
HDR
STD
CH1
CH2
[ + ]
ICONS
VOLUME [ - ]
1
2 3
5
6 7 8
9 10 11 12 13
17
18 19
20 21 22
23
24 25
26
38
28
30
32
41
42
43
29
27
31
39
40
32
44
45
33
34
35
36
37
4
14 15 16
1 Time code
The display will toggle to the next display or no display every time the <COUNTER> button is pressed.
f
[TCG
**
:
**
:
**
:
**
]:
Displays the time code. [TCR
**
:
**
:
**
:
**
] will be displayed during playback.
[TCG] is displayed with black and white inverted during the slave lock into the external input time code.
f
[UBG
**
**
**
**
]:
Displays the user bits. [UBR
**
**
**
**
] will be displayed during playback.
f
[CLIP
*
:
**
:
**
:
**
]:
Displays the counter value of each clip. This is displayed when the [RECORDING] menu
→
[REC COUNTER] is set to
[CLIP]. Displays the counter value of the clip being played back during playback.
f
[
*
:
**
:
**
:
**
]:
Displays the cumulative counter value from the reset position. This is displayed when the [RECORDING] menu
→
[REC
COUNTER]
→
[TOTAL] is set.
2 Frame rate
f
[
**
fps]:
Frame rate is displayed when set to the [SCENE FILE] menu
→
[VFR]
→
[ON].
f
[S.SLOW120]:
Displayed when set to the [SYSTEM] menu
→
[SUPER SLOW]
→
[ON] and the [SYSTEM] menu
→
[FREQUENCY]
→
[59.94Hz].
f
[S.SLOW100]:
Displayed when set to the [SYSTEM] menu
→
[SUPER SLOW]
→
[ON] and the [SYSTEM] menu
→
[FREQUENCY]
→
[50.00Hz].
f
(No display):
It is not displayed when set to the [SCENE FILE] menu
→
[VFR]
→
[OFF] and the [SYSTEM] menu
→
[SUPER SLOW]
→
[OFF].
3 <AUTO/MANUAL> switch
Displayed when the <AUTO/MANUAL> switch is set to <AUTO>.
4
Message display area for stop of cooling fan
Displays a message when the cooling fan has stopped.
5
Recording status (card slot 1)
Displays the recording status of the memory card in card slot 1.
f
:
Not target for recording.
f
(flashing):
Recognizing the memory card.
f
:
The recording is stopped while the recording target memory card is inserted.
f
:
Recording.
f
(Flashing red dot):
Processing to stop the recording.
f
[P ]:
Recording is stopped with pre-recording is enabled and the recording target memory card is inserted.
f
[P]:
Pre-recording is enabled, and the memory card is not inserted in the card slot, or the memory card is not recognized.
f
:
The tally lamp is instructed to illuminate in red via network.
f
:
The tally lamp is instructed to illuminate in green via network while the recording is stopped.
f
(No display):
It is in one of the following conditions.
-
A memory card has not been inserted.
-
The memory card cannot be recognized.
-
The tally lamp is not instructed to illuminate in red/green via network, and the [NETWORK] menu
→
[NETWORK FUNC]
→
[NDI
|
HX] is set.
6
Remaining recording capacity and status of the memory card (card slot 1)
Displays the remaining recording capacity and status of the memory card in card slot 1.
f
[0min] to [999min]:
Remaining recording capacity (999 minutes or more is displayed as [999min])
-
The display will flash when the remaining recording capacity becomes two minutes or less.
-
The recording capacity available for simultaneous recording (recording capacity for the memory card of the two memory cards with less recording
capacity) is displayed when simultaneous recording is performed.
f
[WP]:
Write protected (the write protection switch of the memory card is set to the LOCK side)
f
[END]:
No remaining recording capacity (no remaining recording capacity on the memory card)
f
[ERR]:
A memory card that cannot record is inserted (the card is recognized but cannot record due to a format error, a card other than a memory
card being inserted, etc.)
Summary of Contents for AVC ULTRA AJ-UPX36OED
Page 10: ...Before using the camera read this chapter Chapter 1 Overview ...
Page 191: ...Maintenance of the camera or frequently asked questions are described Chapter 10 Notes ...
Page 201: ...This chapter describes the specifications of this product Chapter 11 Specification ...
Page 210: ...Web Site http www panasonic com Panasonic Corporation 2019 ...