Panasonic AV-HS60C1E, Operation Manual

Page: 145 / 206

– 145 –
Chapter 8 System Menu — System settings
[1F Fix], [2F Fix]
The video is delayed for one frame (1F_Fix) or two frames (2F_Fix).
f
The delay difference during transition (when [SQ], [SL], or [3D] is selected in the wipe pattern) and after transition will
disappear.
f
Only [1F Fix] can be selected in the Standard mode, and [2F Fix] can be selected in the 3G mode and the 4K mode.
r
Setting the delay amount
Item After transition MIX/WIPE SQ/SL/3D
[Minimum] No delay No delay 1 F delay, 2 F delay*
[1F Fix] 1 F delay 1 F delay 1 F delay
[2F Fix] 2 F delay 2 F delay 2 F delay
* It will be one frame (1 F) delay when operating in the Standard mode, and two frames (2 F) delay when operating in the 3G mode and the 4K mode.
Setting the SDI signal ancillary
Set the function to superimpose the ancillary data (V ancillary data and embedded audio data).
f
For SD format: Ancillary data starting in line 12 will be superimposed.
f
For HD format: Ancillary data starting in line 9 will be superimposed.
f
For 3G format (Level B): Ancillary data starting from line nine of LinkA and LinkB is superimposed.
The ancillary data included in the 3G-Level A signal is deleted.
f
The ancillary data is superimposed only to the following signal when operating in the 4K mode.
-
The LinkA signal with smallest number within the four lines of the output signals constructing one 4K signal.
When 1080/59.94i, 720/59.94p, 1080/50i, or 720/50p is selected as the system format of the unit, it is not possible to allow the ancillary data and
embedded audio data to pass through even if SD format signals (480/59.94i or 576/50i) have been input in the [Dot by Dot] mode or [U/C] mode.
For details on [Dot by Dot] mode and [U/C] mode, refer to “Setting the input mode” (page 119).
1
Select the <SYS> button → [SYSTEM] → [Video] tab.
2
Select an item in [AUX] in the [Ancillary1] column.
Configure the setting to superimpose the ancillary data to AUX1 to AUX16 output.
[Off] Does not superimpose the ancillary data.
[On] Superimposes the ancillary data of the source selected in the AUX bus (AUX1 to AUX16).
3
Select an item in [ME PGM] in the [Ancillary] column.
Configure the setting to superimpose the ancillary data to ME1PGM output and ME2PGM output.
[Off] Does not superimpose the ancillary data.
[On]
f
When [BKGD] is selected as the type of the ancillary data for corresponding ME
Superimposes the ancillary data of the source selected in the PGM bus of the corresponding ME.
f
When [KEY1] to [KEY4] is selected as the type of the ancillary data for corresponding ME
Superimposes the ancillary data of the source selected in the KEY1 to KEY4 key fill bus of the corresponding ME.
[AUTO]
f
When [BKGD] is selected as the type of the ancillary data for corresponding ME
Superimposes the ancillary data of the source selected in the PGM bus of the corresponding ME.
f
When [KEY1] to [KEY4] is selected as the type of the ancillary data for corresponding ME
- During the period that the KEY1 to KEY4 in the corresponding ME are turned on
Superimposes the ancillary data of the source selected in the corresponding key fill bus.
- During the period that the KEY1 to KEY4 in the corresponding ME are not turned on
Does not superimpose the ancillary data.
f
For selecting the type of ancillary data for the corresponding ME, refer to Steps
7
and
8
.
4
Select an item in [ME PVW] in the [Ancillary] column.
Configure the setting to superimpose the ancillary data to ME1PVW output and ME2PVW output.
[Off]
Does not superimpose the ancillary data.
[On]
f
When [BKGD] is selected as the type of the ancillary data for corresponding ME
Superimposes the ancillary data of the source selected in the PST bus of the corresponding ME.
f
When [KEY1] to [KEY4] is selected as the type of the ancillary data for corresponding ME
Superimposes the ancillary data of the source selected in the KEY1 to KEY4 key fill bus of the corresponding ME.
[AUTO]
f
When [BKGD] is selected as the type of the ancillary data for corresponding ME
Superimposes the ancillary data of the source selected in the PST bus of the corresponding ME.
f
When [KEY1] to [KEY4] is selected as the type of the ancillary data for corresponding ME
- During the period that the KEY1 to KEY4 in the corresponding ME are turned on
Superimposes the ancillary data of the source selected in the corresponding key fill bus.
- During the period that the KEY1 to KEY4 in the corresponding ME are not turned on
Does not superimpose the ancillary data.
f
For selecting the type of ancillary data for the corresponding ME, refer to Steps
7
and
8
.
5
Select an item in [DSK] in the [Ancillary] column.
f
Sets to superimpose the ancillary data to the DSKPGM output (DSKPGM1/DSKPGM2).
[Off] Does not superimpose the ancillary data.