ELE-27
4-15. Component Y-Pb Timing
Adjustment
BOARD
V OUT (F5)
TP
Y OUT (CH B1), Pb OUT (CH B2)
ADJ.
D06: NENT PB TMG (Service Menu)
TAPE
525(NTSC): VFM3580KM (L)
Alignment Tape (Bow tie portion)
INPUT
-----
MODE
PLAY
M. EQ
Analog WFM (Bow tie mode)
SPEC.
Y Pb Timing : 0
±
5nsec
1.
Set menu setting of SETUP menu as follows.
614 PB / PR OUT LV : M2
2. Open the SERVICE MENU. (Refer to SEC1
Service Information.)
3. Select
the
D00: VOUT ADJUST
and press the
“SET” button to open the VOUT ADJUST MENU.
4. Select
the
D-1: CMPNT ADJUST
and press the
“SET” button.
5. Play back the alignment tape at the Bow tie
portion (18:00-22:00).
6. Adjust
D06: NENT PB TMG
so that the crossing
point of the Bow tie signal becomes a center
(Timing=0
±
5nsec
) as shown bellow.
7.
Set menu setting of SETUP menu as follows.
614 PB / PR OUT LV :
β
CAM
<Note>
Incase of WFM does not have “Bow tie mode” (Y-Pb
timing adjustment mode), if the oscilloscope has
“ADD” and “INVERT” switch, it is possible to make the
following waveform by those switch.
4-16. Component Y-Pr Timing
Adjustment
BOARD
V OUT (F5)
TP
Y OUT (CH B1), Pr OUT (CH B3)
ADJ.
D09: NENT PR TMG (Service Menu)
TAPE
525(NTSC): VFM3580KM (L)
Alignment Tape (Bow tie portion)
INPUT
-----
MODE
PLAY
M. EQ
Analog WFM (Bow tie mode)
SPEC.
Y Pr Timing : 0
±
5nsec
1.
Set menu setting of SETUP menu as follows.
614 PB / PR OUT LV : M2
2. Open the SERVICE MENU. (Refer to SEC1
Service Information.)
3. Select
the
D00: VOUT ADJUST
and press the
“SET” button to open the VOUT ADJUST MENU.
4. Select
the
D-1: CMPNT ADJUST
and press the
“SET” button.
5. Play back the alignment tape at the Bow tie
portion (18:00-22:00).
6. Adjust
D09: NENT PR TMG
so that the crossing
point of the Bow tie signal becomes a center
(Timing=0
±
5nsec
) as shown bellow.
7.
Set menu setting of SETUP menu as follows.
614 PB / PR OUT LV :
β
CAM
<Note>
Incase of WFM does not have “Bow tie mode” (Y-Pr
timing adjustment mode), if the oscilloscope has
“ADD” and “INVERT” switch, it is possible to make the
following waveform by those switch.
0 ± 5nsec
Center
Y OUT
+
Pr OUT
(CH B1-CH B3)
Y OUT
+
Pb OUT
(CH B1-CH B2)
0 ± 5nsec
Center
Summary of Contents for AJSD955B - DVCPRO50 STUDIO DECK
