100
8-4
VF
8-4-1
VF DISPLAY
8-4-2
VF MARKER
8-4-3
USER BOX
The ____ in the Adjustable Range column indicates the preset
mode.
Items/
Data Saved
Adjustable
Range
Remarks
DISP
CONDITION
NORMAL
HOLD
NORMAL:
Display status constantly.
HOLD:
Display status only when the
MODE CHECK switch is pressed.
– C U F E
DISP MODE
1
2
3
Set the DISP MODE.
Switch the camera’s Warning/Message
indication. Please refer to [4-7-4 Display
Modes and Setting Changes/adjustment
Result Messages] for more information.
– C U F E
VF OUT
Y
NAM
R
G
B
Select the VF output.
Y:
Brightness signal
NAM:
Output signal with the highest level
among R, G, and B signals.
R:
Rch signal
G:
Gch signal
B:
Bch signal
– C U F E
VF DTL
0
:
3
:
5
Select the VF DTL.
Additionally enhance the DTL for the VF
signal. 0 setting is the same DTL as the
primary scan lines.
– C U F E
ZEBRA1
DETECT
0%
:
70%
:
109%
Set the ZEBRA1 detection level (IRE value).
– C U F E
ZEBRA2
DETECT
0%
:
85%
:
109%
Set the ZEBRA2 detection level (IRE value).
– C U F E
ZEBRA2
ON
SPOT
OFF
Set the ZEBRA2 to ON, OFF, or SPOT.
– C U F E
LOW LIGHT LVL OFF
10%
15%
20%
25%
30%
35%
Set the camera incoming light volume at
which to display LOW LIGNT.
– C U F E
ECU MENU
DISP.
ON
OFF
Set the menu display on the VF to ON or
OFF when the ECU is connected.
– C U F E
50M
INDICATOR
ON
OFF
Set the 50M recording indication to ON or
OFF.
– C U F E
MARKER/CHAR
LVL
50%
60%
70%
80%
90%
100%
Adjust the brightness of markers and
characters displayed on the VF.
– C U F E
Items/
Data Saved
Adjustable
Range
Remarks
TABLE
A
B
Select the VF MARKER setting table.
First, select table A or B, then set the items
below for each table.
– C U F E
CENTER MARK OFF
1
2
3
4
Switch the centre mark.
OFF:
Do not display centre mark.
1:
+ (large)
2:
Hollow (large)
3:
+ (small)
4:
Hollow (small)
– C U F E
SAFETY ZONE OFF
1
2
Select the frame type for the safety zone.
OFF:
Do not display frame.
1:
Box
2:
Corner frame
– C U F E
SAFETY AREA 80%
:
90%
:
100%
Set the position of the safety zone.
– C U F E
FRAME SIG
4:3
13:9
14:9
VISTA
Set the frame marker.
Only enabled when REC MODE is set to
16:9.
The VISTA ratio is 16:8.65.
– C U F E
FRAME MARK ON
OFF
Set the frame marker to ON or OFF.
– C U F E
FRAME LVL
0
:
15
Set the level outside the frame marker.
0:
Equivalent to signal OFF.
15:
Same brightness as centre area.
This setting, however, is disabled if
the FRAME SIG is set to VISTA.
– C U F E
Items/
Data Saved
Adjustable
Range
Remarks
USER BOX
ON
OFF
Select whether or not to display the USER
BOX.
– C U F E
USER BOX
WIDTH
1
:
13
:
100
Set the width of the USER BOX.
– C U F E
USER BOX
HEIGHT
1
:
13
:
144
Set the height of the USER BOX.
– C U F E
USER BOX H
POS
–50
:
+00
:
+50
Set the horizontal position of the USER
BOX.
– C U F E
USER BOX V
POS
–144
:
+000
:
+144
Set the vertical position of the USER BOX.
– C U F E
Summary of Contents for AJ-SPX800E
Page 117: ...117 9 MEMO...
