23
3
Chapter 3 Recording and Playback
(continued)
Removing P2 Cards
1
While pressing down the slide lock button, move the
slide-out door to the left.
The door opens.
2
Tilt down the EJECT button.
3
Then, depress the EJECT button to release the P2 card
so that you can remove it.
<Notes>
z
When a P2 card is being accessed or it is being
recognised after insertion (P2 CARD ACCESS LED blinks
in orange), do not remove the P2 card.
If your AJ-SPC700P is not set to turn on the P2 CARD
ACCESS LED, before removing the card ensure that pre-
recording and/or voice memo recording have finished (the
P-REC indication has stopped blinking and the V mark or
VOICE REC indication on the viewfinder screen has
turned off) after stopping recording or playback.
z
If a P2 card being accessed is removed, the viewfinder
displays “TURN POWER OFF” and the AJ-SPC700P
gives a warning using an alarm and the WARNING LED.
In addition, all P2 CARD ACCESS LEDs blink rapidly in
green. If this is the case, turn the power off. For more
information on warning indications, see [7-3 Warning
System].
z
If a P2 card is removed while being accessed, clips on it
may become irregular although the data will not be
corrupted. Check the clips and restore them if required.
For more information about how to restore clips, see [6-9
Restoring Clips].
z
If a P2 card being formatted is removed, it may be not be
formatted properly. In this case, the viewfinder displays
“TURN POWER OFF”. If this message appears, turn off
the power, then restart the AJ-SPC700P to reformat the
card.
z
If a P2 card is inserted while another P2 card is being
played back, the inserted P2 card is not recognised and
the P2 CARD ACCESS LED for that card does not come
on. Card recognition starts when the playback ends.
<For Your Information>
The P2 CARD ACCESS LEDs may be set to stay off using
the menu option ACCESS LED. This option can be found on
the <SYSTEM MODE> screen, which is accessible from the
SYSTEM SETTING page.
To Prevent Accidental Erasure of P2 Card Content
To prevent the content of a P2 card being accidentally
erased, position the write-protect switch on the P2 card at
[Protect].
<Note>
Write-protect switchover can be performed while the card is
being accessed (during recording or playback), but does not
take effect until access to the card ceases.
* The mode check indication is shown in the viewfinder. For more
information, see [4-7-2 Viewfinder Status Indication Layout].
Depress the tilted-down
EJECT button to release
the P2 card.
Tilt down the EJECT
button.
P2 CARD ACCESS LED and status of P2 cards
P2 CARD
ACCESS LED
MODE CHECK
indication*
Status of P2 Card
Stays on in green ACTIVE
Writing and reading
enabled
Stays on in
orange
ACTIVE
Writing and reading
enabled. The card is
recordable (loop recording
also enabled).
Stays on in
orange or green
ACTIVE !
Writing and reading
enabled. However, some
clips recorded on the P2
card may not be able to be
read successfully.
Blinks in orange
ACCESSING
Writing or reading being
performed.
Quickly blinks in
green
INFO READING
The P2 card is being
recognised.
Blinks in green
FULL
The P2 card has no free
space. Only reading is
enabled.
PROTECTED
The write-protect switch on
the P2 card is positioned at
[PROTECT]. Only reading
is enabled.
Stays off
NOT
SUPPORTED
The card is not supported
by your AJ-SPC700P.
Replace the card.
FORMAT ERROR
The P2 card is not properly
formatted. Reformat the
card.
NO CARD
No P2 card is inserted.
Protect
Write-protect switch
#,52%2'PINKUJDQQMࡍࠫ㧞㧜㧜㧡ᐕ㧝㧞㧤ᣣޓᧁᦐᣣޓඦᓟ㧝㧞ᤨ㧠㧥ಽ
