Panasonic AJ-SPC700, Operating Instructions Manual

Page: 105 / 124

105
8
Chapter 8 Menu Description Tables
(continued)
8-3-7 ADDITIONAL DTL 8-3-8 SKIN TONE DTL
<Note>
The items indicated by
„
are the setting items for PAINT
MENU SW( „ ) R/W in the <SD CARD R/W SELECT>
screen. The items without
„
are the setting items for PAINT
MENU LEVEL R/W.
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
The ____ in the Adjustable Range column indicates the
preset mode.
Items/
Data Saved
Adjustable
Range
Remarks
KNEE APE LVL OFF
1
2
:
5
Set KNEE APE LEVEL.
S C U F E
CHROMA DTL OFF
1
:
5
Set the chroma detail.
Detects the chroma edge and
superimposes it on Y to enhance
H.DTL. A greater value increases the
correction.
S C U F E
DTL GAIN(+) –31
:
+00
:
+31
Adjust the detail level
(upwards).
S C U F E
DTL GAIN(–) –31
:
+00
:
+31
Adjust the detail level toward the –
(downwards).
S C U F E
DTL CLIP 00
:
63
Adjust the detail signal clip towards the
+ direction.
S C U F E
DTL SOURCE (R+G)/2
(G+B)/2
2G+R+B /4
(3G+R)/4
R
G Set the signal source for detail signal
components.
S C U F E
H.DTL LINE MIX 0H
1H
2H
Set the scan line to generate the H.DTL
signal.
S C U F E
„
CORNER DTL ON
OFF
ON/OFF switching for CORNER DTL
mode, which enhances the resolution
around the screen perimeter.
S C U F E
Items/
Data Saved
Adjustable
Range
Remarks
„ SKIN TONE
DTL
ON
OFF Set the skin tone DTL to ON or OFF.
S C U F E
„ SKIN TONE
ZEBRA
ON
OFF ON/OFF switching for ZEBRA within
the SKIN TONE range.
S C U F E
SKIN DTL
CORING 0
:
5
:
7
Adjust the effect of SKIN TONE DTL
CORING.
S C U F E
SKIN TONE
GET Used when obtaining the target hue for
SKIN TONE DTL. Align the center
marker and the target object with each
other.
– – – – –
Y MAX 000
:
190
:
255
Set the maximum value of the
brightness signal to which SKIN TONE
effect is enabled.
S C U F E
Y MIN 000
:
010
:
255
Set the minimum value of the
brightness signal to which the SKIN
TONE effect is enabled.
S C U F E
I CENTER 000
:
022
:
255
Set the center position on the I axis (the
area where SKIN TONE is enabled).
S C U F E
I WIDTH 000
:
010
:
255
Set the area width where SKIN TONE
is enabled along the I axis above and
below the I CENTER.
S C U F E
Q WIDTH 000
:
005
:
255
Set the area width where SKIN TONE
is enabled along the Q axis above and
below the I CENTER.
S C U F E
Q PHASE –128
:
+000
:
+127
Set the phase in the area where SKIN
TONE is enabled based on the Q axis.
S C U F E
R-Y
B-Y
Q-WIDTH
I-WIDTH
Q-PHASE
I-CENTER
Y
Y-MAX
Y-MIN
0
–
direction
+ direction
= SKIN TONE AREA
#,52%2'PINKUJDQQMࡍ࡯ࠫ㧞㧜㧜㧡ᐕ㧝㧞᦬㧤ᣣޓᧁᦐᣣޓඦᓟ㧝㧞ᤨ㧠㧥ಽ