Panasonic AJ-PX5000G, Operating Instructions Manual

Page: 179 / 260

– 179 –
Chapter 7 Menu Operations — Menu list
[GENLOCK]
Item Description of settings
[GENLOCK] Switches the synchronization signal of the camera signal.
[INT]: Synchronizes to the internal standard signal independent of standard signals input to the
<GENLOCK IN> terminal or <SDI IN> terminal.
[GL IN]: Synchronizes to the standard signal input to the <GENLOCK IN> terminal.
[SDI IN]: Synchronizes to the standard signal input to the <SDI IN> terminal.
f
Factory setting: [INT]
When the main menu → [SYSTEM] → [SYSTEM MODE] → [REC SIGNAL] is set to [SDI], the camera
synchronizes to the reference signal input to the <SDI IN> terminal regardless of this setting.
[GL PHASE] Selects the output signal of phase to be locked to the signal input to the <GENLOCK IN> terminal.
[HD SDI]: Locks the HD SDI output signal to genlock input. The video start position of the down converter
output signal lags by approx. 90 lines.
[COMPOSITE]: Locks the down converter output signal to genlock input. The video start position of the
HD SDI output signal advances by approx. 90 lines.
f
Factory setting: [HD SDI]
This item is not displayed in SD mode (480/59.94i and 576/50i).
[H PHASE COARSE] Roughly adjusts to match horizontal synchronization phase when building a system.
[ − 100]…[100]
f
Factory setting: [0]
[H PHASE FINE] Minutely adjusts to match horizontal synchronization phase when building a system.
[ − 100]…[100]
f
Factory setting: [0]
[MIC/AUDIO]
Item Description of settings
[VR SELECT] Selects which channel to assign to the <AUDIO LEVEL CH1/3>/<AUDIO LEVEL CH2/4> and <F.AUDIO
LEVEL> dials.
[CH1/2]: Assigns level adjustment of channels 1/2. Channels 3/4 can be automatically adjusted or adjusted
by [LVL CONTROL CH3] or [LVL CONTROL CH4].
[CH3/4]: Assigns level adjustment of channels 3/4. Channels 1/2 can be automatically adjusted or adjusted
by [LVL CONTROL CH1] or [LVL CONTROL CH2].
f
Factory setting: [CH1/2]
When [CH3/4] is selected in [VR SELECT], channels are also replaced for the following six items.
f
[FRONT VR CH1] → [FRONT VR CH3]
f
[FRONT VR CH2] → [FRONT VR CH4]
f
[AUTO LVL CH3] → [AUTO LVL CH1]
f
[AUTO LVL CH4] → [AUTO LVL CH2]
f
[LVL CONTROL CH3] → [LVL CONTROL CH1]
f
[LVL CONTROL CH4] → [LVL CONTROL CH2]
For details, refer to “Adjusting the recording levels” (page 69).
[FRONT VR CH1(CH3)] Sets whether to enable the <F.AUDIO LEVEL> dial for input signals selected in audio CH1 (CH3).
[FRONT]: Enabled only when [FRONT] is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when [REAR] is selected.
[ALL]: Enabled when any input is selected.
[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial
is turned.
f
Factory setting: [OFF]
The channel is replaced when [CH3/4] is selected in [VR SELECT]. Setting values are inherited between
replaced channels.
[FRONT VR CH2(CH4)] Sets whether to enable the <F.AUDIO LEVEL> dial for input signals selected in audio CH2 (CH4).
[FRONT]: Enabled only when [FRONT] is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when [REAR] is selected.
[ALL]: Enabled when any input is selected.
[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial
is turned.
f
Factory setting: [OFF]
The channel is replaced when [CH3/4] is selected in [VR SELECT]. Setting values are inherited between
replaced channels.
[AUTO LVL CH3(CH1)] Selects whether to automatically adjust the level adjustment method for audio CH3 (CH1).
[ON]: Automatic adjustment is enabled.
[OFF]: Automatic adjustment is disabled. Can be adjusted using [LVL CONTROL CH3(CH1)] at this time.
f
Factory setting: [ON]
The channel is replaced when [CH3/4] is selected in [VR SELECT]. Setting values are inherited between
replaced channels.
[AUTO LVL CH4(CH2)] Selects whether to automatically adjust the level adjustment method for audio CH4 (CH2).
[ON]: Automatic adjustment is enabled.
[OFF]: Automatic adjustment is disabled. Can be adjusted using [LVL CONTROL CH4(CH2)] at this time.
f
Factory setting: [ON]
The channel is replaced when [CH3/4] is selected in [VR SELECT]. Setting values are inherited between
replaced channels.