Panasonic AJ-PX5000G, Operating Instructions Manual

Page: 178 / 260

– 178 –
Chapter 7 Menu Operations — Menu list
Item Description of settings
[CENTER MARK] Switches the center marker.
[1]: + (large)
[2]: Open center (large)
[3]: + (small)
[4]: Open center (small)
[OFF]: Does not display.
f
Factory setting: [1]
[SAFETY MARK] Selects the type of frame for the safety zone marker.
[1] Box
[2] Corners
[OFF]
Does not display.
f
Factory setting: [2]
If the main menu → [I/F SETUP] → [DOWNCON SETTING] → [DOWNCON MODE] is set to [SIDE CROP]
or [LETTER BOX], the safety zone marker is not displayed to the down converter output signal in HD
mode.
[SAFETY AREA] Sets the size of the safety zone marker.
The constant ratio of length to width can be set in 1% increments.
[80%]…[100%]
f
Factory setting: [90%]
[FRAME MARK] Enables/disables frame marker.
[ON], [OFF]
f
Factory setting: [OFF]
[FRAME SIG] Sets frame marker aspect ratio.
[4:3], [13:9], [14:9], [VISTA], [CNSCO]
f
Factory setting: [4:3]
[VISTA] is 16:8.65, and [CNSCO] is 16:6.81.
[USER BOX] Sets whether to display the user box to the signal from the monitor output terminal (<SDI OUT2>, <HDMI
OUT>, or <VIDEO OUT>).
[ON], [OFF]
f
Factory setting: [OFF]
If the main menu → [I/F SETUP] → [DOWNCON SETTING] → [DOWNCON MODE] is set to [SIDE CROP]
or [LETTER BOX], the user box is not displayed to the down converter output signal in HD mode.
[USER BOX WIDTH] Sets the width of the user box.
[1]…[100]
f
Factory setting: [13]
[USER BOX HEIGHT] Sets the height of the user box.
[1]…[100]
f
Factory setting: [13]
[USER BOX H POS] Sets the horizontal position of the center of the user box.
[
−
50]…[50]
f
Factory setting: [0]
[USER BOX V POS] Sets the vertical position of the center of the user box.
[ − 50]…[50]
f
Factory setting: [0]
[DOWNCON SETTING]
Item Description of settings
[DOWNCON MODE] Sets the mode of the down converter output signal.
[SIDE CROP], [LETTER BOX], [SQUEEZE]
f
Factory setting: [SQUEEZE]
When [LETTER BOX] is selected, some parts of the top and bottom edges of the down converter output
video may be distorted. This is not a malfunction.
[DETAIL] Turns detail function for the down converter output signal [ON]/[OFF].
The down converter output signal contains detail components set during HD signal processing.
This setting superimposes the detail components exclusive to down converter output to that signal.
[ON], [OFF]
f
Factory setting: [ON]
Even if this setting is [OFF], the detail components set during HD signal processing cannot be disabled.
[H.DTL LEVEL] Sets horizontal detail correction level for the down converter output signal.
[0]…[31]
f
Factory setting: [8]
[V.DTL LEVEL] Sets vertical detail correction level for the down converter output signal.
[0]…[31]
f
Factory setting: [4]
[DTL CORING] Sets the detail noise removal level.
[0]…[15]
f
Factory setting: [1]
[H.DTL FREQ.] Selects the horizontal detail frequency.
[2.5MHz], [3MHz], [3.5MHz], [4MHz], [4.5MHz]
f
Factory setting: [3.5MHz]
[2D LPF] Sets the filter.
[ON]: Reduces cross colors.
[OFF]: Does not reduce cross colors.
f
Factory setting: [OFF]