22
Parts and their Functions: Shooting and Recording/Playback Functions Section
30. DVCPRO connector
This is an output connector for video, audio, and data
that comply with the IEEE1394 standard.
Notes
Power is not supplied from the unit.
Be absolutely sure to bear the following points in mind
when connecting the IEEE1394 cable (DV cable).
– Ensure that the connections with other devices are
made on a 1:1 basis.
– When a 1394 cable (DV cable) has been connected
to the DVCPRO connector, do not apply any strong
external force as this may damage the connector.
– When error code 1394 E-92 (1394 INITIAL
ERROR) appears, disconnect the connecting
cables and re-connect them or turn off the unit’s
power and turn it back on.
– Ensure that the unit and all of the connected
devices are each grounded (or connected to a
common ground) before use.
If it is not possible to ground the unit and devices,
turn off the power of the unit and of all the
connected devices before connecting or
disconnecting the IEEE1394 cable.
– When the unit is to be connected to a device
equipped with a 4-pin type of connector, connect
the unit’s connector (6-pin type) first.
– When connecting the unit with a PC equipped with
a 6-pin type of connector, connect the 1394 cable
as dictated by the shapes of the 1394 connectors.
Bear in mind that inserting a plug the wrong way
round may damage the unit.
– When the unit is used in AVC-Intra format, image/
audio signals cannot be output through the
DVCPRO connector.
31. REMOTE (remote control) connector
The remote control unit AJ-RC10G (optional) is
connected here.
32. Option slot
Attach the video encoder card (AJ-YAX800G, optional).
For information about the installation and proxy
recording, see the AJ-YAX800G instruction manual.
33. SD memory card insertion slot
An SD memory card (optional) is inserted here. SD
memory cards are used for recording and accessing the
menu settings of cameras and the lens files, uploading
metadata, and proxy recording (optional).
<Cautions in using SD memory cards>
Use the unit by inserting an SD memory card that is
compliant with the SD standard or the SDHC standard.
MultiMediaCards cannot be used. (Bear in mind that
recording may no longer be possible if you do use
them.)
If you intend to use miniSD cards in unit, always install
the adapter specially designed for miniSD cards. (The
unit will not work properly if only the miniSD card
adapter is installed. Make sure that the card has been
installed in the adapter before using it.)
Use of Panasonic’s SD memory cards and miniSD
cards is recommended. Be sure to format cards using
unit.
Any SD memory card and SDHC memory card with the
following capacities can be used with the unit.
To record proxy (optional), use an SD memory card with
a capacity of 256 MB, 512 MB, 1 GB, or 2 GB labeled
“High Speed” or use an SDHC memory card.
For the latest information not available in the operating
instructions, visit the P2 Support Desk at the following
Web site.
34. Busy (operation mode display) lamp
This lamp indicates the active status of the SD memory
card.
It stays illuminated when the card is active.
Note
While the lamp is on, do not insert or remove the card.
6-pin type
4-pin type
SD memory card
8 MB, 16 MB, 32 MB, 64 MB,
128 MB, 256 MB, 512 MB, 1 GB,
2 GB
SDHC memory card
4 GB, 8 GB, 16 GB, 32 GB
https://eww.pavc.panasonic.co.jp/pro-av/
The SDHC card conforms to a new standard for memory
cards with a large capacity of more than 2 GB which
was established by the SD Association in 2006.
The SD card logo is a registered trademark.
MMC (MultiMediaCard) is a registered trademark of
Infineon Technologies AG.
AJ-HPX2700G-VQT1V27_eng.book 22 ページ ２００８年９月２日 火曜日 午後５時４３分
