Panasonic AJ-CX4000, Operating Instructions Manual

Page: 143 / 223

– 143 –
Chapter 5 Shooting — Display of the viewfinder status
Screen display during shooting
TCG 1 2 : 3 4 : 5 6 : 2 8
2160-59.94p
MOV 420 150M
A001C001
1A
IP REMOTE
36dB +12↑ 1/10000 F5.6
S B H.SENS. DEC 3 1 2 0 1 9 1 0 : 4 5 : 3 0
LOW LIGHT
AUTO KNEE:ON 65%
Z000
MF00
D2x
MKR:A
ATW
S/H INTRVL
HD
14.6V
999min 999min
FBC
RELAY
HDR CAC
+ CH1
CH2
eP2
R E C
REC
B . D E V
1:F 2:W
EX
1 4 5 7 8 9 10 11 12 13
39 38 37 35 36 34 31 33 32 29 30 27 28 25 26
48
20
21
22
47
46
49
45
18
19
23
24
44
43
42
41
40
3 6 14 15 16 17 2
1 Time code/User bits/Counter data
Displays the time data selected with the <DISPLAY> switch.
f [TCG ** : ** : ** : ** ]: Displays the time code. [TCR ** : ** : ** : ** ] will be displayed during playback.
[TCG] is displayed with black and white inverted during the slave lock into the external input time code.
f [UBG ** ** ** ** ]: Displays the user bits. [UBR ** ** ** ** ] will be displayed during playback.
f
[CLP
**
:
**
:
**
:
**
]:
Displays the counter value of each clip. This is displayed when the [RECORDING] menu → [REC COUNTER] → [CLIP] is
set. Displays the counter value of the clip being played back during playback.
f [ ** : ** : ** : ** ]: Displays the cumulative counter value from the reset position. This is displayed when the [RECORDING] menu → [REC
COUNTER] → [TOTAL] is set.
2 Bonding Device Status
Displays the device status received from the bonding device with up to first five letters and the following symbol.
f : The signal reception strength of the bonding device is displayed in 6 levels.
f : The remaining battery of the bonding device is displayed in 6 levels.
f : Displayed when there is an error in the bonding device.
f (No display): Bonding device is not connected.
3 Recording status
f [REC]: Recording.
f [REC] (Flashing): Processing to stop the recording.
f [P]: Recording is stopped with pre-recording is enabled.
f (No display): It is in one of the following conditions.
- Recording is stopped with pre-recording is disabled.
- It is set to the [NETWORK] menu → [NETWORK FUNC] → [NDI | HX].
4 Recording media
Setting status of the [RECORDING] menu → [REC MEDIA] is displayed.
f
[eP2]:
Displays when set to the [RECORDING] menu → [REC MEDIA] → [expressP2].
f [mP2]: Displays when set to the [RECORDING] menu → [REC MEDIA] → [microP2/SD].
f (No display): Set to the [NETWORK] menu → [NETWORK FUNC] → [NDI | HX].
5 Status of the card slot 1 or 2
Displays status of the card slot 1 when the [RECORDING] menu → [REC MEDIA] → [expressP2] is set.
Displays status of the card slot 2 when the [RECORDING] menu → [REC MEDIA] → [microP2/SD] is set.
The status are as follows:
f : Not target for recording.
f (flashing): Recognizing the memory card.
f : Recording target.
f
(No display):
It is in one of the following conditions.
-
A memory card has not been inserted.
-
The memory card cannot be recognized.
-
It is set to the [NETWORK] menu → [NETWORK FUNC] → [NDI | HX].
6 Remaining capacity and status of the memory card in card slot 1 or 2
Displays the remaining capacity and status of the memory card in card slot 1 or 2.
f [0min]…[999min]: Displays remaining capacity of the memory card. Remaining capacity of 999 minutes or more is displayed as [999min].
- The display will flash when the remaining capacity of the memory card becomes two minutes or less.
- The remaining capacity of the memory card available for simultaneous recording (remaining capacity for the memory card of the two memory
cards with less remaining capacity) is displayed when simultaneous recording is performed.
f [WP]: It is write protected. The write-protected switch on the memory card is set to the Protect side or the LOCK side.
f [END]: Memory card has no remaining capacity.
f [ERR]: Memory card that cannot record is inserted. Displayed when the card is recognized but cannot be used, such as having a format error, or
not being a memory card.