manualshive.com logo in svg

Panasonic AGM1CSRX16T, Reference Manual

Share
Download
Panasonic AGM1CSRX16T Reference Manual Download Page 103

Cautions for Proper Use

● Practical considerations for exporting the product or assembly containing the product

When the end user of the product or end use of the product is associated with military affair

or weapon, its export may be controlled by the Foreign Exchange and Foreign rade Control

Law. Complete review of the product to be exported and export formalities should be

practiced.

● This product is intended to be used with a general industrial product, but not designed or

manufactured to be used in a machine or system that may cause personal death when it is

failed.

● Installation, wiring, operation, maintenance, etc., of the equipment should be done by

qualified and experienced personnel.

● Install a safety equipments or apparatus in your application, when a serious accident or loss

of property is expected due to the failure of this product.

● This product is designed for general industrial equipments.Don´t use this product under

special conditions such as nuclear energy control, aerospace equipments, transportation,

medical equipment, various safety equipments or special equipments.

● The wiring condition(earth wire method and cables length and shield cable condition of signal

lines) may affect the noise resistance,please confirm the noise resistance of the machine.

● Failure of this product depending on its content, may generate smoke of about one cigarette.

Take this into consideration when the application of the machine is clean room related.

● Product overload can cause the goods to fall,please follow the marking.
● Do not use benzine, thinner, alcohol, acidic cleaner and alkaline cleaner because theycan

discolor or damage the exterior case.

● This product shall be treated as industrial waste when you dispose.
● This product related standards,laws and the user is responsible for matching between

machine and components in terms of configuration, dimensions, life expectancy,

characteristics, when installing the machine or changing specification of the machine. The

user is also responsible for complying with applicable laws and regulations.

● The product will not be guaranteed when it is used outside its specification limits.
● Parts are subject to minor change to improve performance.

Cautions for Proper Use

WUME-GM1H-01

App-3

Summary of Contents for AGM1CSRX16T













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands