Panasonic AG-CX350, Operating Instructions Manual

Page: 191 / 216

– 191 –
Chapter 9 Network Connection — Streaming function
[SYSTEM] menu [NETWORK] menu → [STREAMING]
[FREQUENCY] [REC FORMAT] [STREAMING FORMAT]
[50.00Hz] [1080-50.00p/AVC-I100]
[1080-50.00p/AVC-I422]
[1080-50.00p/AVC-G25]
[1080-50.00p/AVC-G12]
[1080-50.00p/422LongGOP 100M]
[1080-50.00p/422ALL-I 200M]
[1920 × 1080-50fps 24M]
[1920 × 1080-50fps 20M]
[1920 × 1080-50fps 16M]
[1280 × 720-50fps 14M]
[1280 × 720-50fps 8M]
[1280 × 720-50fps 3M]
[640 × 360-25fps 4M]
[640 × 360-25fps 1.5M]
[640 × 360-25fps 0.7M] (Factory setting)
[320 × 180-25fps 4M]
[320 × 180-25fps 1.5M]
[320 × 180-25fps 0.5M]
[1080-50.00i/AVC-I200]
[1080-50.00i/AVC-I100]
[1080-50.00i/AVC-I50]
[1080-50.00i/AVC-G50]
[1080-50.00i/AVC-G25]
[1080-50.00i/AVC-G12]
[1080-25.00p/422LongGOP 50M]
[1080-25.00p/422ALL-I 100M]
[1080-50.00i/422LongGOP 50M]
[1080-50.00i/422ALL-I 100M]
[1920 × 1080-25fps 14M]
[1920 × 1080-25fps 6M]
[1920 × 1080-25fps 1M]
[1280 × 720-25fps 8M]
[1280 × 720-25fps 2M]
[1280 × 720-25fps 1M]
[640 × 360-25fps 4M]
[640 × 360-25fps 1.5M]
[640 × 360-25fps 0.7M] (Factory setting)
[320 × 180-25fps 4M]
[320 × 180-25fps 1.5M]
[320 × 180-25fps 0.5M]
[720-50.00p/AVC-I200]
[720-50.00p/AVC-I100]
[720-50.00p/AVC-I50]
[720-50.00p/AVC-G50]
[720-50.00p/AVC-G25]
[720-50.00p/AVC-G12]
[1280 × 720-50fps 14M]
[1280 × 720-50fps 8M]
[1280 × 720-50fps 3M]
[640 × 360-25fps 4M]
[640 × 360-25fps 1.5M]
[640 × 360-25fps 0.7M] (Factory setting)
[320 × 180-25fps 4M]
[320 × 180-25fps 1.5M]
[320 × 180-25fps 0.5M]
Starting streaming with an operation from the application software
1
Select the [NETWORK] menu → [STREAMING] → [START TRIGGER] → [RECEIVER].
2
Specify the IP address and the path of the camera with the application software as follows, and start streaming.
rtsp://(IP address)/stream
@ @
NOTE
t Perform an operation from the application software to stop streaming.
t Only RTSP is available when starting streaming with an operation from application software.
t For details about the operations to start streaming from the application software, please see the manual for each application software.
t Streaming stops when performing operations such as displaying the thumbnail screen or playing back clips on the camera.
t Streaming may stop when the date/time is set while streaming.
Streaming with multicast
One streaming can be distributed to multiple receivers via supported router, etc., when the multicast function is used.
1
Select the [NETWORK] menu
→
[STREAMING]
→
[START TRIGGER]
→
[RECEIVER(MULTICAST)].
2
Select the [NETWORK] menu → [STREAMING], and specify [MULTICAST ADDRESS] and [MULTICAST PORT].
f Set [MULTICAST ADDRESS] within following range.
IPv4: 224.0.1.0 to 239.255.255.254
IPv6: Multicast address starting with FF
f Set [MULTICAST PORT] within the range of 1024 to 50000.
3
Specify the address of the camera and start streaming with the application software.
@ @
NOTE
t Multicast cannot start streaming with the operation on the camera.
t Disable the LAN card not to be used when receiving the multicast image to be displayed on a computer with multiple LAN cards installed.
Starting streaming with an operation on the camera
1
Select the [NETWORK] menu → [STREAMING] → [START TRIGGER] → [CAMERA].
2
Set the destination.
For details of setting the destination, refer to “Setting the destination for streaming in the menu of the camera” (page 192) or “Referring to the
memory card for the destination of streaming” (page 192).