W
ARNING:
ALL
PERSONS
USING
THIS
EQUIP
MENT
MUST
READ
AND
UNDERST
AND
ALL
INSTRUC
TIONS.
FAIL
URE
TO
DO
SO MA
Y RESU
LT
IN SERIOUS INJU
RY
OR DEA
TH. USERS SHOULD
BE
FA
MILIAR WITH
PERTINENT
REGULA
TIONS
GOVERNING THIS
EQUIP
MENT
. ALL
INDIVIDU
ALS WHO
USE THIS
PRODU
CT
M
UST
BE
PROPER
LY
INSTRU
CT
ED
ON
HOW
TO
USE
THE
DEVICE.
AVOID
CO
NT
AC
T
WITH
PHY
SICAL
HAZARDS
(T
HERMAL,
CHEMICAL,
ELEC
TRICAL,
ET
C.). MAKE ONL
Y CO
MP
AT
IBLE
CO
NNEC
TIONS.
Compliance: OSHA 1926.502, OSHA 1910.66, ANSI Z359.1(07), ANSI Z359.7(11)
EN 795:1996 Class B (CE 0321)
Remo
vable
Concr
et
e A
nchor
1”
H
ole
. 10000 LBS
Conf
orms t
o ANSI Z359.1-2007
M
odel: A3410000
Ba
tch# RB10-
XX
X
MFD: MM/Y
YY
Y
Stainless Steel, Aluminium, Zinc Plated Copper, 7x19 Aircraft Cable
Pat # 7,357,363 B2 / 7,011,281 B2 / US 6,729,821 B2
Max
WARNING:
ALL PERSONS USING THIS EQUIPMENT MUST
READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO
SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD
BE FAMILIAR WITH PERTINENT REGULATIONS GOVERNING THIS
EQUIPMENT. ALL INDIVIDUALS WHO USE THIS PRODUCT MUST
BE PROPERLY INSTRUCTED ON HOW TO USE THE DEVICE. AVOID
CONTACT WITH PHYSICAL HAZARDS (THERMAL, CHEMICAL,
ELECTRICAL, ETC.). MAKE ONLY COMPATIBLE CONNECTIONS.
Phone: 845-548-5655
TAP!!!
DO NOT REMOVE
WARNING LABEL!
CE 0321 / EN 795:1996 Class B
Compliance: OSHA
1926.502 & 1910.66 /
ANSI Z359.1
DO NOT REMOVE
May be used as an anchor point for a leading edge restraint
system. See optional anchor points below for example. The
use of two anchors is not required for leading edge restraint
systems unless otherwise specified by the manufacturer.
WORK SURFACE
Stainless Steel,
Aluminum, Zinc Plated Copper
, 7x19
Aircraft Cable
OPTIONAL
(ANCHOR POINTS)
WORK SURFACE
(ANCHOR POINT)
Concrete must be 3000-
psi or higher and fully
cured. Installation loca-
tion to be approved by
a qualified person.
MINIMUM CLEARANCE 3ft (1m)
DECK/FLOOR/GROUND LEVEL
W
ARNING!!! SWING F
ALLS M
AY OC
CUR
WHEN
THE
W
ORKER IS NO
T DIREC
TL
Y UNDER ANCHOR POINT
.
All products subjected to fall arresting forces should be removed
from service immediately!
DRILLING & INSTALLATION INSTRUCTIONS:
1.
Drill a 1” (25mm) diameter hole at least 4.5” (114mm) deep. The
drilled hole must be straight and perpendicular to the surface.
Make sure the hole is of uniform diameter and free of peaks and
valleys on the inner wall.
2.
Blow hole clean with compressed air.
3.
Always inspect the hole carefully when reusing a
previously drilled hole.
4.
When placing anchor, place your thumb inside the anchor loop
and your first two fingers around the trigger. Squeeze fingers and
thumb together till the trigger and spring fully compress.
5.
Insert unit at least 4” (101mm) deep into hole and release the
trigger. Do not force.
6.
Set the unit with a slight tug on the anchor loop.
7.
The stop sleeve must always be partially inserted into the hole.
REMOVAL INSTRUCTIONS:
1.
When removing anchor, place your thumb inside the anchor loop
and your first two fingers around the trigger. Squeeze fingers and
thumb together till the trigger and spring fully compress.
2.
While squeezing the trigger pull the anchor out of the hole.
3.
If the anchor becomes stuck, insert a punch, screwdriver or other
object into the hole until it touches the top of the cleaning bushing.
4.
Lightly tap with a hammer making sure the tool is touching the top
of the cleaning bushing while squeezing the trigger (cleaning
bushing should be easily visible at the edge of the hole).
5.
If tool was required to remove the anchor, inspect thoroughly for
damage after removal. If damage is found remove from service and
destroy immediately.
*The user shall be equipped with
a means of limiting the maximum
dynamic forces exerted on the
user during the arrest of a fall to a
maximum of 8 kN (1350-lbf).
PERFORMANCE:
Static Tensile Strength:
10,000-lbf (44kN)
Maximum Capacity:
One worker with
max weight of 310-lbs (140kg) when used
as a single point anchorage connector for
personal fall arrest or restraint system
DIMENSIONS:
Weight:
1-lbs (453g)
Length:
13.75” (349mm)
Diameter
1” (25mm)
REGULATORY COMPLIANCE:
ANSI Z359.1-2007, ANSI Z359.7-2011
OSHA 1926.502, OSHA 1910.66,
EN
795:1996 Class B CE0321
COMPONENT MATERIALS:
Aluminum:
Trigger
Aircraft Cable:
Main Cable, Activator Wire
Polyurethane:
Loop Cover
Stainless Steel:
Cone, Spoons, Stop Sleeve
Zinc Plated Steel:
Spring
Zinc Plated Copper:
Swage
min from an
y edge
10”
drill
1”
Ø (25mm)
10”
90º
90º
0º
PROPER LOADING
Good
Best
See Spoon Orientation
Good
See Spoon Orientation
*Best practice for spoon orientation
when loaded 90º to hole.
SPOON ORIENTATION
Best
Ok
Load
Load
=
=
1.5” (38mm)
Cleaning Bushing
Cleaning Ferrule
7” (178mm)
End Termination
Stop Sleeve
Spring
Swage
13.75” (349mm)
Heavy Duty Return Wire
Trigger
Anchor Loop
3” (76mm)
2” (50.8mm)
Spoon
Main Cable
