Palfinger MBB C 500 VAN Operating Instructions Manual Download Page 138

Page: 138 / 196

138

Retractable Models

Conical lubricating head

Roll-off protection bearings and joint of folding platform

Sliding consoles in the guide rails (nozzle lubrication)

To grease and lubricate:



Clean the conical lubricating heads.



Use a grease gun to press grease into the conical lubricat-
ing heads

(44)

until the bearing is filled (see chapter “Lubri-

cants and Operating Media” from p. 188).



Lubricate the bearings of the rool stop and the joint in the
platform

(45)



Lubricate the sliding consoles in the guide rails

(46)

(see

chapter “Lubricants and Operating Media” from p. 188).

F G

Betriebsanleitung_Hubladebuehnen_EN.book Seite 138 Donnerstag, 15. August 2019 4:04 16

Summary of Contents for MBB C 500 VAN





































































































































































































Search results

Summary of Contents for MBB C 500 VAN

Reviews:

Palfinger MBB C 500 VAN, Operating Instructions Manual, Page: 138 / 196

Search results

Summary of Contents for MBB C 500 VAN

Reviews: