PairGain 150-2230-01 Quick Installation Manual Download Page 37

Page: 37 / 48

350-819-300-01, Revision 01

System Configuration

ELU-819 List 1

January 10, 2000

Table 6.

Information Displayed in Main Console Screen

Field

Description

Circuit Configuration

G.703

Identifies the LTU and NTU G.703 ports.

n TS

Indicates the number of G.703 time slots (n) selected for the G.703
application interface.

V.35

Identifies the NTU V.35 port.

V.36

Identifies the NTU V.36 port.

RS-449

Identifies the NTU RS-449 port. (RS-530 supersedes RS-449, but
does not display on the main console screen. RS-449 must be
selected to use the RS-530 interface.)

X.21

Identifies the NTU X.21 port.

n k

Indicates the data rate selected for the Nx64K application interface.

RPF/WETTING

Indicates RPF or WETTING mode for Remote Power Feed. Nothing is
shown when NONE is selected.

Timing

No selection available.

G.703

Clock extracted from G.703 data stream.

CRC4 Mode

N/A

CAS Mode

Select the multiframe alignment mode for the G.703 interface.

INSERT

Inserts a multiframe alignment code into time slot 16 of frame 0 and
11011101 into time slot 16 of frames 1 through 15.

PASSTHRU

Time slot 16 is passed through unchanged at the G.703 port.

IDLE

Inserts the user-selected idle code into time slot 16 at the G.703 port.

Application Mode

Indicates application mode selected.

STRUCT

With framing.

UNSTRUCT

No framing.

PTM

System operates in the point-to-multipoint mode. Two pairs of a
single LTU connect to two different NTUs.

TSP

Time-slot prioritization with framing.

SINGLE

Single pair with framing.

Summary of Contents for 150-2230-01

















































Search results

Summary of Contents for 150-2230-01

Reviews:

Brands by name

Popular brands

PairGain 150-2230-01, Quick Installation Manual

Search results

Summary of Contents for 150-2230-01

Reviews:

Brands by name

Popular brands