12
Aqua-Mex
MA40-12E
ENGLISH
N
N
L1
L1
1~230V
AC
J5:
FLOW
J2:
AC IN
J6:
PUMP
J3:
TEMP
L1
L1
N
Switch panel
N
+45°
E10042-0
100426 OA
Aqua MEX ( 1N~ 230V )
Art.no.
Rev.no.
Scale
Designed by:
Approved by:
Revised by: Date
Drawn by: Date
Drawing number
Assembly drawing no.
Surface treatment
part of ISO 2768-1
The tolerance class in accordance with this
E
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
11395X
OA 2010-05-19
OA
2010-08-31
flödesriktning
Aqua MEX fully equipped
M11234 1
Th
is
do
cu
m
en
ta
nd
its
co
nt
en
ts
ar
e
th
e
ex
cl
us
iv
e
pr
op
er
ty
of
P
ah
lé
ns
an
d
m
ay
no
tb
e
co
pi
ed
,
re
pr
od
uc
ed
,t
ra
ns
m
itt
ed
or
co
m
m
un
ic
at
ed
to
a
th
ird
pa
rty
,o
ru
se
d
fo
ra
ny
pu
rp
os
e
w
ith
ou
tw
rit
te
n
pe
rm
is
si
on
.
A
B
⇒
⇒
⇒
⇒
⇒
⇒
¨
¨
¨
¨
¨
¨
¨
¨
Primary connection
Do not dismount
A
Standard Aqua-Mex:
1. Fit the two wall mounting brackets. Each bracket has 2 holes Ø6, c/c 91 mm. Note the c/c distance between the brackets for
each model, see the dimension diagram.
2. Place the heat exchanger in the brackets.
3. Connect the secondary circuit (the pool water).
4. Screw the brackets together.
After this, the pool’s circulation system can be started up.
5. Connect the primary circuit. NB! The primary and secondary circuits’ flow shall be in opposite
directions for maximum effect.
6. Check that the connections do not leak.
7. Bleed the primary circuit.
NB: The heat exchanger’s existing nipples (A) on the primary circuit must not be removed.
Electrical installation (only for Aqua-Mex FE)
• Electrical installation shall always be carried out
by an authorized electrician.
• The Aqua-Mex FE shall be installed with a
protective ground and an earth fault relay.
However, the pump in the Aqua-Mex FE does
not require any external automatic circuit
breaker for the motor protection.
• The electrical cable must be installed such that
it under no circumstances gets into contact with
the piping and/or the pump and motor housing.
Alternative flow direction
(only for Aqua-Mex FE)
The fully equipped Aqua-Mex FE can easily adjust
the heat exchanger’s flowdirection to suit the
existing installation.
Aqua-Mex FE is supplied in version A.
If version B is required, follow steps 1-7 below:
1. Undo the screws.
2. Undo the screws
of the bracket.
4. Rotate the bracket,
make sure the cables run free.
3. Lift the bracket with
the control box on.
7. Fasten the
screws on the
cover. Done!
6. Screw the
bracket into
place.
5. Rotate it a total
of half a turn.
