background image

                    OPERATING & MAINTENANCE

INTRODUCTION                                            INSTRUCTIONS

READ THIS BOOK

This operator’s book has important information for the use
and safe operation of this machine.  Read this book care-
fully before starting the machine.  Keep this book and tell
all operators to read the book.  If you do not follow the
instructions, you can cause an injury or damage equipment,
furniture or buildings.

For new books write to:
               Pacific Steamex, Inc.
               2259 S. Sheridan
               Muskegon, MI  49442-6252

Carefully inspect all components to ensure that there is no
concealed freight damage.  If such damage is discovered,
file a “CONCEALED DAMAGE REPORT” immediately
with the delivering carrier.

The contents of this manual are based on the latest product
information available at the time of publication.  Pacific
Steamex reserves the right to make changes or improve-
ments to its machines without notice.

FOR YOUR CONVENIENCE, RECORD THE
FOLLOWING IMPORTANT INFORMATION:

MODEL_______________________________

SERIAL NUMBER_______________________

PART NUMBER ________________________

DATE PURCHASED _____________________

TRIUMPH

870, 1190 & MX-21

SELF-CONTAINED

CARPET EXTRACTORS

Summary of Contents for TRIUMPH 1190













Reviews: