Pacific hydrostar 99741 Set Up And Operating Instructions Manual Download

Page: 3 / 23

For technical questions, please call 1-800-444-3353;

troubleshooting section at end of manual.

SKU 99741

PAGE 3

SaVe thIS manual

Keep this manual for the safety warn-

ings and precautions, assembly, operat-

ing, inspection, maintenance and cleaning

procedures. Write the product’s serial

number in the back of the manual near the

assembly diagram (or month and year of

purchase if product has no number). Keep

this manual and the receipt in a safe and

dry place for future reference.

ImPOrtant SaFetY

InFOrmatIOn

In this manual, on the labeling,

and all other information provid-

ed with this product:

this is the safety alert

symbol. It is used to alert

you to potential personal

injury hazards. Obey all

safety messages that

follow this symbol to avoid

possible injury or death.

danger indicates

a hazardous

situation which, if not

avoided, will result in death or

serious injury.

WarnIng

indicates a

hazardous situation which, if

not avoided, could result in

death or serious injury.

cautIOn, used

with the safety

alert symbol, indicates a

hazardous situation which, if

not avoided, could result in

minor or moderate injury.

nOtIce is used to

address practices

not related to personal injury.

cautIOn, without

the safety alert

symbol, is used to address

practices not related to

personal injury.

general Pressure Washer Safety

Warnings

WarnIng read all safety

warnings and instructions.

Failure to follow the warnings and

instructions may result in electric

shock, fire and/or serious injury.

Save all warnings and

instructions for future reference.

Work area safety

Keep work area clean and well lit.

Cluttered or dark areas invite acci-

dents.
Do not operate pressure washers in

explosive atmospheres, such as in

the presence of flammable liquids,

gases or dust. Pressure washers

create sparks which may ignite the

dust or fumes.
Keep children and bystanders away

while operating a pressure washer.

Distractions can cause you to lose

control.

electrical safety

Pressure washer plugs must match

the outlet. Never modify the plug in

any way. Do not use any adapter

plugs with grounded pressure wash-

ers. Unmodified plugs and match

Summary of Contents for 99741
























Search results

Summary of Contents for 99741

Reviews:

Related manuals for 99741

Brands by name

Popular brands

Pacific hydrostar 99741, Set Up And Operating Instructions Manual

Search results

Summary of Contents for 99741

Reviews:

Related manuals for 99741

Brands by name

Popular brands