Pacific hydrostar 99741 Set Up And Operating Instructions Manual Download

Page: 22 / 23

For technical questions, please call 1-800-444-3353.

SKU 99741

PAGE 22

If the steps above do not solve the problem or if the repairs involved are

too complex, contact a qualified technician.

Shut off the Pressure Washer, release all pressure in a safe

manner, and disconnect it from power and water before adjusting,

cleaning, or repairing the unit.

troubleshooting

(continued)

Pressure changes during use

air may be getting in the water supply

hose, check all connections.

retighten

connections.

check that tip is free from

debris and deposits.

all cOnnectIOnS

are tIght

cOnnectIOnS

are lOOSe

tIP IS

clean

tIP IS

dIrtY

clean tip.

Internal valves or seals

may be worn or sticking,

contact a qualified

technician.

detergent will not dispense

Verify that proper type of pressure

washer detergent is being used and

that the low pressure setting is being

used, see pages 10-11, #3.

nOn-PreSSure

WaSher detergent

uSed

remove the handle

and thoroughly rinse

out the detergent

bottle and passages.

Refill with correct

detergent.

cOrrect detergent

and SettIngS

uSed

IncOrrect

SettIng uSed

Set up the washer as

explained on page

10.

remove the handle and

check that the suction tube

is not bent or pinched.

Summary of Contents for 99741
























Search results

Summary of Contents for 99741

Reviews:

Related manuals for 99741

Brands by name

Popular brands

Pacific hydrostar 99741, Set Up And Operating Instructions Manual

Search results

Summary of Contents for 99741

Reviews:

Related manuals for 99741

Brands by name

Popular brands