PACH & COMPANY QUANTUM Q5VOIP, Quick Manual

Page: 1 / 3

•
Missing Parts, contact Pach and Company 1-888-678-
7224
•
Defective system under manufacturer warranty,
call 1-888-678-7224 for advance replacement
•
24 Months warranty for complete system
•
6 Months warranty for Printed Circuit Board
•
Manuals, management software, catalog are on CD or
download at www.pach-co.com
Exit program, cancel call 25 Keypad beep
0= disable (default)
1=enable
Save program 26 Door beep
0= disable
1= enable (default)
00 Change master code (0000
is default) 27 Talk time (060-240
second). Default=60
second
01 Add new forwarding
tenant’s directory 28 Unlock relay1 time
(12-99 second).
Default= 12 second
02
Edit existing tenant’s
directory
29 Unlock relay2 time
(12-99 second).
Default= 12 second
03
Delete existing tenant’s
directory
30 Call Forwarding
0= disable 1= enable
04 Clear all forwarding
tenant’s directory 31 Call forwarding time
05-60 second
05 Call Forwarding 32 Forwarding directory
0-9
06 New access code 33 Temporary code
07 Delete access code 34 Special code
08 Clear all access code 35 Temporary card
09 Access code digit (4-8
digit). Default is 4-digit 36 Special card
10 Add new card 37 Initiate premise call
0=**, 1=## (default)
11 Delete card 38 System acknowledge
(0-9). Default= 3
12 Clear all card 39 Remote access
0= disable
1=enable (default)
13 Set time 40 DTMF relay 1 (1-9).
Default=9
14 Set date 41 DTMF relay 2 (1-9).
Default=8
15 Initializing event recording 42 Relay 2 Mode
1= door control (default)
2= relay 2 trigger
simultaneously as relay 1
3= enable if function code
24 is enable
4= turn relay 2 on and off
On=7, Off=6
16 AUS= auto unlock schedule
(0-9 schedule) 43 DND: do not disturb
time zone (0-9)
17 TMZ= time zone. 20 TMZ,
00-20. 44 Disable Time zone relay
1, 2 or both
18 HLD= holiday zone. 20
HLD, 1-20 45 Relay 1 and 2 unlock
timer
20 AUXIN1
0= disable (default)
1= enable control by relay 1
open interval
2= relay 1 control by AUXIN1
46 Firmware version
21 AUXIN2
0= disable (default)
1= enable control by relay 2
open interval
2= relay 2 control by AUXIN2
48 PBX enable. Default=
disable
22 Do not disturb
0= disable (default), 1=
enable
23 Lock-out Count 49 Edit Access code
24 Alarm
0= disable
1= local beep for 60 seconds
2= disable system for 60
seconds with no beep
3= call directory (0-9)
50 Erase the memory to
factory default
51 Welcome screen
Log on to programming: Press
and simultaneously then release,
the welcome message will stop
scrolling (repeat if screen still scrolls)
enter 4-
digit “
MASTER CODE
” (0000
is default), the screen will show:
Select the “
Function Code
” from the
table
OPERATION
Opening the door remotely press (relay 1) or (relay 2)
Opening the door with the access code press (display screen
will stop scrolling) then press a valid 4-digit access code.
Extending talk time tenant must press from the phone after the
time out warning beep.
Calling into the system from premise location (Intercom)
1. Press or depending on function code 37, then
press to communicate with the person
Calling into the system from remote location :
Enable function code 39
1. Call the system phone number, hear one beep if the system
answering the call.
2. Press then 4-digit master code, hear one short beep
3. Press to establish two way communication
4. Press or to release the door.
Call waiting: function code 38 must be set 1-9 and function code 39
can be set either 1 or 0, press on your phone to transfer between
calls
See Function Code 37
Premise
Relay 1 Relay 2
Open cycle ##9/**9 ##5/**9
Open hold ##8/**8 ##4/**4
Close ##7/**7 ##3/**3
OPERATION
TO CALL FROM THE SYSTEM
1. INTERCOM MODE PRESS
2. CALL FORWARDING MODE, press to scroll name from A-Z or
to scroll name from Z-A then press to call name selected.
Opening the door remotely press (relay 1) or (relay 2)
QUANTUM Q5VOIP SERIES
PACH AND COMPANY INC. QUICK GUIDE