manualshive.com logo in svg

Pace Technologies NANO 2000T, Instruction Manual, Page: 13 / 52

Share
Download
Pace Technologies NANO 2000T Instruction Manual Download Page 13

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  ▲           

I

NSTRUCTION 

M

ANUAL 

3601 E. 34th St. Tucson, AZ  85713  USA  Tel. +1 520-882-6598  Fax +1 520-882-6599  email: [email protected]    Web: http://www.metallographic.com 

 

Please read this instruction manual carefully and follow all installation, operating and safety guidelines. 

NANO 2000T Polisher 

9 

4.3   Grinding / polishing by hand 

1. 

Install working wheel and attach grinding papers / polishing cloths. 

2. 

Switch on the machine in the back and set the mode, speed, and time (if required). 

3.   

Position flexible water spout over working wheel.  During sample preparation adjust water 
flow by turning water control knob as required.  Note:  Initial operation of water valve may 
contain air in the lines.  Turn water on slowly to purge air from system. 

4. 

Press START/STOP start and stop the machine in the manual mode.   

4.2.1   Direction and speed controller (manual) 

1.  To change direction of the wheel: 

 
-Press clockwise or counter clockwise button, 
LED will light 

2.  To change the speed of the wheel: 

 
Select low, medium or high speed fast buttons 
and use up and down arrows to fine tune speed 
if required 

Fast speed buttons 

4.2.1   Programmable Mode 

  To change the speed setting for 

the fast speed buttons use the 
following procedure:

 

 

Press the PRG button and use 
the up and down keys to SL 
(slow speed) and press ENTER.  
Use the up and down < key to 
change the speed.  Use Sn for 
changing the medium speed 
and SH for the fast speed. 

1
. 

The programming mode can be used to pre-set the 
polishing speed, direction and time for automated 
polishing.  It can also be used to change the fast speed 
buttons. 

2
. 

To change the speed of the wheel: 
 
Press the PRG button and use the up and down keys 
to SP1 and press ENTER.  Use the up and down < key 
to change the speed.  Press ENTER to save. 

3
. 

To program a grinding/ polishing time: 
 
Press the PRG button and use the up and down keys 
to t1 and press ENTER.  Use the up and down < key to 
change the time (enter in seconds - displayed min-sec) 

4
. 

To operate the pre-programmed conditions: 
 
PRESS the AUTO button and then start the program 
with the RUN/STOP button.  The pre-programmed 
conditions will be executed. 

Summary of Contents for NANO 2000T





















































Reviews:

No comments