PAC RPK4-GM2301 Quick Start Manual Download Page 1

Complete Radio Replacement Kit with 

Vehicle Information Retention for 

Select 11-Bit GMLAN Vehicles

RPK4-GM2301

Pacific Accessory Corporation

Rev. 072517

Page 1

© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.

PAC-audio.com

Parts List

The RPK4-GM2301 includes everything you need for a professional installation of an aftermarket radio in your 11-Bit GM 

Vehicle. 
This kit contains:

1. Dash kit 

1a. (x1) Double DIN mounting panel

1b. (x1) Single DIN radio ISO mount trim ring 

1c.  (x1) LCD adapter bracket (for single DIN applications)

1d. (x1) Pocket (for single DIN applications) 

1e. (x8) Radio mounting screws

1f.  (x1) USB cover (for when USBDMA1 or USBDMA6 is not used with our kit)

1g. (x2) Radio mounting brackets (one left and one right)

2. Radio replacement interface module

3. Radio connection harnesses

4. PAC-LCD

Overview

The RPK4-GM2301 is a complete radio replacement kit with vehicle information retention for select 11-Bit GMLAN Vehicles. This kit utilizes a 

user friendly LCD display with onboard buttons to view and adjust vehicle information and settings. The included radio replacement interface 

will retain factory steering wheel controls (SWC) and allows you to program two radio functions to each SWC button by using short press long 

press dual command functionality. The interface also provides data bus driven outputs such as retained accessory power (RAP), illumination, 

vehicle speed sensor (VSS), reverse trigger and parking brake.

Table of Contents:                                                                        Page:

1. Factory Radio Removal --------------------------------------------------------- 2

2. Radio Replacement Installation and Wiring Instructions --------------- 3

3.

 

Steering Wheel Control Programming --------------------------------- 3-4

4. Dash Kit Assembly --------------------------------------------------------------- 5

5. Using the PAC-LCD -------------------------------------------------------------- 6

1. If a double DIN radio is being installed with this kit, enough wire has been supplied to mount the LCD in the glove box or center console area.
2. The interface comes pre-programmed for all of the vehicle’s factory SWC functions and does not require programming, unless you wish to 

re-assign the SWC functions, or utilize short press long press dual command functionality. The SWC can always be restored to default settings 

by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to flash 3 times.

3. 

The LED will flash whenever a SWC button is pressed.

4. The Interface has the ability to retain the warning chimes and audible turn signal clicks through its onboard piezo. This feature is on by default. 

This can be disabled using the supplied PAC-LCD. For more info on disabling the chimes through the module see page 6.

Important Notes

1a.

3.

1d.

1c.

2.

1b.

4.

1e.

1f.

1g.

Summary of Contents for RPK4-GM2301







Reviews: