background image

DRAFT 5

11

OXE 200 HP 3.5” DISPLAY  MANUAL

SETTINGS

Number of engines

This setting represents how many engines are connected to the CAN bus. This is the TOTAL number of engines. 
When using 3.5” displays, each engine requires a separate display. This setting must be correct and match what 
is configured in the Engine Control Unit (ECU). Entering the wrong setting may result in errors and false data 
being displayed. For single engine installations this should always be set to 1.

Engine No.

This setting represents what engine this display should connect to. For single engine installations this should 
always be set to 1. 

Unit system

Metric or Imperial.
Metric will display data in kPa and °C
Imperial will display data in psi and °F

Fuel sender

The display can handle three types of fuel senders.

 

-

European standard analogue sender (0-190 Ω)

 

-

US standard analogue sender (240-30 Ω)

 

-

NMEA2000 digital signal over CAN bus

The analogue senders should be connected with one pin to ground and one to pin 7 on the secondary connector 
at the back of the display.

Bleep

Turn button sound on/off.

Display screen ID

Enable/disable display of identifying number when switching to screen 1, 2 or 3.

FUNCTION DESCRIPTION

Summary of Contents for 3,5" Display





















Reviews: