Owon SDS1000 User Manual Download Page 9 | Manualshive

Page: 9 / 68

background image

3.Quick Start

4

3. Quick Start

Introduction to the Structure of the Oscilloscope

This chapter makes a simple description of the operation and function of the front
panel of the oscilloscope, enabling you to be familiar with the use of the
oscilloscope in the shortest time.

Front Panel

The front panel has knobs and function buttons. The 5 buttons in the column on
the right side of the display screen are menu selection buttons, through which, you
can set the different options for the current menu. The other buttons are function
buttons, through which, you can enter different function menus or obtain a specific
function application directly.

3

5

6

1

2

7

4

Figure 3-1 Front panel

1.  Display area
2.  Menu selection buttons: Select the right menu item.
3.  Control (button and knob) area
4.  Probe Compensation: Measurement signal (5V/1kHz) output.
5.  Signal Input Channel
6.

USB Host port:

It is used to transfer data when external USB equipment

connects to the oscilloscope regarded as "host device".

For example: Saving

the waveform to USB flash disk needs to use this port.

7. Power on/off

«
...
7
8
9
10
11
...
»

Summary of Contents for SDS1000





































































Reviews:

No comments

Related manuals for SDS1000

Brand: Raymarine Pages: 70

Brand: Harbor Freight Tools Pages: 4

BELMONT 2001039

Brand: Backyard Discovery Pages: 50

Brand: Backyard Discovery Pages: 45

Brand: Backyard Discovery Pages: 70

Brand: BACtrack Pages: 16

Brand: Nektar Pages: 3

Brand: Youkey Pages: 86

Brand: Wacker Neuson Pages: 62

Sportsound SSR-200

Brand: Daktronics Pages: 5

Brand: p-light Pages: 28

Brand: SAMCHULLY Pages: 48

Brand: HAGS Pages: 5

Brand: HAGER WERKEN Pages: 2

Brand: IEMCA Pages: 82

KID 80-IV Touch

Brand: IEMCA Pages: 122

Brand: Calrec Pages: 92

Brand: Safety 1st Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands