Quick Start Guide
–1–
–2–
–3–
NEOs
™
StorageLoader
®
1U Tape Library
Step 1
It is
essential
that you activate your warranty. Technical and warranty support are
not available
until the warranty is active:
For an existing customer:
1.
http://support.overlandstorage.com/
support
page.
2.
Enter your
e-mail address
and
password
in the
appropriate fields, and then press
Enter
or click the
right arrow (
>
).
3.
At the Support Home page, click
Register New
.
4.
Enter the requested information and click
Submit
.
Your warranty certificate will be emailed to you. Follow the instructions in the
email to complete the process.
For a new customer:
page and follow the instructions.
You’ll receive a confirmation e-mail from Overland with instructions on how to
complete the registration process.
Step 2
Optional Components
WARNING:
To reduce the risk of electric shock or damage to equipment, always
remove any power cords while working with the unit.
WARNUNG:
Um das Risiko eines elektrischen Schlags oder Schäden am Gerät zu
vermeiden, ziehen Sie stets den Netzstecker, bevor Sie an der Einheit arbeiten.
AVERTISSEMENT:
Pour réduire le risque de choc électrique ou endommagement de
l'équipement, retirez toujours les cordons électriques en travaillant avec l'appareil.
Any optional internal components need to be installed before continuing. Refer to the
installation instructions and warnings that are packaged with the components.
The tape drives are installed in
.
Step 3
Prepare for Installation
NOTE: If the temperature in the room where the library will be installed varies by 15º C
(30º F) from the room where the library was stored, allow the library to acclimate to the
surrounding environment for at least 12 hours before unpacking it.
1.
Unpack the
library and components
, placing them on a secure surface.
2.
Remove the
shipping lock
:
a.
Remove the
yellow label
on the top that is securing the shipping lock.
b.
Remove the
shipping lock
from the slot underneath the label.
Store the shipping lock in the slot in the power supply should it needed later.
c.
Replace the
yellow label
back over the slot.
Step 4
The NEOs StorageLoader comes with a sliding rail rack kit for easy installation into a
19-inch (EIA-310) rack.
IMPORTANT: Two-post telco-style or other racks less than 29 inches in depth will NOT
support this unit.
Install the Rack Rails
1.
Determine the
location
where the library is to be installed and mark each
vertical rail on the rack.
NOTE: Verify that the rails are mounted level and at the same rack height on each side.
Store Here
2.
Using the correct screws for your type of rack, secure
one rail
using four screws,
two front and two rear.
3.
for the
other rail
on the other side.
Attach Mounting Brackets
Using the four T10 Torx screws, attach the mounting brackets to each side of the front
of the library.
Install the Library in Rack
WARNING:
It is recommended that a mechanical lifter (or at least two people) be
used to raise and align the unit to prevent injury during installation. Use care when
inserting or removing a unit into or out of a rack to prevent the accidental tipping of
the rack, causing damage or personal injury.
WARNUNG:
Um Verletzungen zu vermeiden, empfehlen wir zur Rack-Installation oder
-Deinstallation die Nutzung einer mechanischen Hebehilfe (oder mindestens zwei
Personen). Seien Sie vorsichtig bei der Rack-Installation oder -Entnahme, um ein
versehentliches Kippen des Racks zu vermeiden und das Rack nicht zu beschädigen
bzw. sich selbst zu verletzen.
AVERTISSEMENT:
Afin d’éviter des blessures pendant l’installation, il est
recommande d’utiliser un monte-charge (ou au moins deux personnes) pour élever
ou aligner l’appareil. Faites attention lorsque vous insérez ou retirez l’appareil d’un
support, pour empêcher le déversement accidentel de la crémaillère causant des
dommages et des blessures.
1.
Using the mechanical lifter, position the
library
in front of the rack.
*10400893*
10400893
