manualshive.com logo in svg

oventrop Regtronic RH HT, Installation And Operating Instructions For The Specialised Installer, Page: 16 / 56

Share
Download
oventrop Regtronic RH HT Installation And Operating Instructions For The Specialised Installer Download Page 16

16

Installation

Commissioning

Settings

Data comm

unication

Tr

oubleshooting

en

Main menu 
Status
Heating
Arrangement
HQM
Basic settings
SD card
Manual mode
User code
In- / Outputs

Arrangement
Optional functions

Optional functions
DHW heating
Th. Disinfection
Circulation
Transmission station

Heating
System
Shared relays
Heating circuits
Optional functions
Screed drying

The menu items and adjustment values 
selectable are variable depending on ad-
justments  already  made.  The  figure  only 
shows an exemplary excerpt of the com-
plete menu in order to visualise the menu 
structure.

Basic settings
Language
Temp. Unit
Flow Unit
Press. Unit
Energy Unit
Auto DST
Time
…
Scheme
Reset

In- / Outputs
Modules
Inputs
Outputs

5 

Functions and options

5.1 

Menu structure

Optional functions
Heat exchange
Return preheating
Solid fuel boiler
Mixer
Parallel relay
Irradiation switch
Zone loading
Error relay
Function block

Shared rel.
Demand 1
Demand 2
Pump 1
Pump 2
Valve 1
Valve 2

Demand 1
Relay
0-10 V
Minimum runtime

Summary of Contents for Regtronic RH HT

























































Reviews:

No comments