background image

OPERATING INSTRUCTIONS 

BEFORE FIRST USE AND AFTER EVERY GAS 
CYLINDER CHANGE, GAS DELIVERY SYSTEM 
MUST BE PURGED OF AIR BEFORE IGNITING! TO 
DO THIS, TURN THE CONTROL KNOB ANTI-
CLOCKWISE TO THE PILOT SETTING. PRESS KNOB 
IN AND HOLD FOR 3 MINUTES BEFORE 
ATTEMPTING IGNITION. 

BATTERY REPLACMENT
Remove impulse ignition capfrom Burner Assembly 
(J)by turning cap counterclockwise. Install 1 AA

TO LIGHT THE PILOT 

 Check all connections prior to each use. 
 

Turn on main gas supply at source. 

 

Press to turn control knob anti-clockwise to 

PILOT

, see right photo. 

 

Hold knob depressed, press 

IGNITION 

button repeatedly until pilot flame is lit, then 

continue to hold the knob depressed for 10 seconds until the pilot remains it after 
releasing knob. 

 

If pilot fails to ignite or alight, press to turn knob clockwise to 

OFF 

and repeat. 

TO LIGHT THE PATIO HEATER 

 The pilot should be lit and the knob set to 

PILOT

 Hold knob depressed gently and turn anti-clockwise to 

LOW

 When mesh glows lit, turn knob clockwise from 

Low 

to 

HIGH 

as needed. 

Note: The burner may be noisy when initially turned on. To eliminate excessive noise 
from the burner, turn the control knob to the pilot position. Then turn the knob to the 
level of heat desired. 

RE-LIGHTING 

 Turn Control Knob to OFF.
 Wait at least 5 minutes, to let gas dissipate, before attempting to re-light pilot.
 Repeat the "Lighting" steps.

TO EXTINGUISH 

 Hold knob depressed &turn the knob clockwise to 'OFF'
 Close the valve of the gas cylinder or the regulator after use. 
 Close the gas bottle and allow this appliance to cool before moving the appliance.

Note: After use, some discoloration of the emitter screen is normal. Close regulator 
after use, allow the appliance to cool before moving. 

IMPORTANT SAFETY RULES 

For use outdoors or in amply ventilated areas.
An amply ventilated area must have a minimum of 25% of the surface 
area open.
The surface area is the sum of the walls surface.
The use of this appliance in enclosed areas can be dangerous and is 
PROHIBITED. 
Children and adults should be aware of the high operatingtemperatures 
of areas above the post when operating this heater. 
Children should be carefully supervised when in the vicinity of the 
heater.
NEVERhang anything, including clothes or any other flammable items, 
on this heater. 
DO NOToperate this heater unless it is fully assembled with its reflector 
in place.
Respect the minimum clearances from combustible materials.

Summary of Contents for 842-192

















Reviews: