English
13w Craft Carry Case
INS130068 REV112613
13w Craft Carry Case
KCY008 CDO-039
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form
and return it today by mail, or register online by going to:
http://warranty.OttLite.com.
WARNING:
To prevent electric shock, make sure the lamp is not
plugged in until all assembly steps are complete.
LAMP ASSEMbLy
NOTE: THIS UNIT IS FULLy ASSEMbLED
1.
Remove all packing from lamp and place base
(A)
on a flat
steady surface.
2.
First step in opening your Craft Carry Case is to open center
clasp
(C)
located on handle
(b)
. Locate clasp side with three
raised dots and pull upward as show in
diagram 1
.
3.
After opening clasp
(C)
, separate and place both sides of
handles
(b)
downward onto their resting position as shown in
diagram 2
.
4.
Open slide-locks
(D)
by sliding bar inward then proceed to
carefully position Craft Carry Case as displayed in
diagram 3
.
Position base
(A)
as desired.
5.
Raise the shade
(H)
from its closed position by grasping
the shade and lifting. Hold the base steady as needed when
raising the shade.
6.
To install tube
(I)
, follow
TUbE INSERTION/
REPLACEMENT
instruction.
7.
Adjust the position of the shade
(H)
by grasping the arms
(J)
to move them into position. Shade
(H)
can swivel and rotate.
8.
Adjust arm tension by using a coin to rotate nuts
(K and L)
clockwise to tighten and counterclockwise to loosen. The
lower joint tension
(Q)
is adjusted by using the provided tool
(R)
, see
diagram 7
for tool storage.
NOTE: Lower joint
tension (Q) cannot be seen in diagram 4 due to its
hidden location.
Always replace the tool
(R)
in its holder
after use.
DO NOT OVERTIGHTEN
arm or lower tension
joint as it may damage them.
9.
Carefully unwrap the cord
(F)
from its cradle inside the base
(A)
. See
diagram 5
.
10.
Plug the cord into a standard 120Vac outlet.
11.
To turn the lamp ON or OFF depress the pushbutton switch
(M)
located in the front of the base
(A)
.
12.
Compartments doors
(N)
can easily open by grasping tabs
(O)
and pulling upward. Compartment dividers
(P)
can
be removed as desired to adjust compartment space; see
diagram 6
.
13.
To secure or close Craft Carry Case, loosen the tension nuts
(K and L)
if needed, place the shade into its closed position
and secure compartment doors. Once carrying case is closed,
close slide-locks
(D)
sliding bar outward and close center
clasp
(C)
.
14.
To stow or carry the Craft Carry Case, unplug the cord and
carefully wrap it into its cradle in the bottom of base
(A)
following direction of “arrow” only.
NOTE:
For safety, place
end of cord on clip
(G)
as shown in
diagram 5
.
CAUTION:
• SECURE COMPARTMENTS PRIOR TO STOWING
PRODUCT.
• TURN OFF THE LAMP WHEN THE SHADE IS
CLOSED.
• DO NOT FORCE THE ARMS TO ANy POSITION.
15.
The auxiliary outlet
(E)
is available for use with two-prong,
polarized 120 VAC tools of less than 700 watts. Outlet
(E)
is
NOT
controlled by the lamp switch and can be used when the
lamp is turned off.
TUbE INSERTION/REPLACEMENT
1.
Make sure that the lamp is not plugged into an electrical
socket.
2.
If the lamp has been in use, allow it to cool approximately 5
minutes before proceeding.
3.
Raise the shade
(H)
to an upright position.
AVOID TUbE bREAKAGE by CAREFULLy REMOVING
TUbE FROM SHADE
4.
If a tube
(I)
is already installed in the lamp, remove it by
grasping it at the free end with your thumb and forefinger.
Angle the tube
(I)
down slightly and, while holding the shade
(H)
steady, pull the tube from its socket.
5.
Install the tube
(I)
by placing the tube into the socket with the
pins aligned with the socket holes. Rotate the tube up to be
even with the shade then give a firm press on the tube base
and end at the same time; a click should be heard as the tube
seats into the socket. Give a slight tug on the tube to confirm it
is being held by the socket.
Please note that in operation, OttLite bulbs are not
dimmable.
Enjoy your 13w Craft Carry Case!
This lighting system is designed for use with
OttLite type
(style number PL13-E). Use of
other products voids the warranty and may result
in damage to the lighting system.
CAUTION!
If the external flexible cable or cord of this
luminaire is damaged, it shall be exclusively replaced by the
manufacturer or its service agent or a similar qualified person
in order to avoid a hazard. Indoor use only.
CAUTION!
To prevent electric shock, match wide blade
of plug to wide slot, fully insert.
CAUTION! ImpOrTANT sAfeTy
INsTrUCTIONs:
This portable lamp has a polarized
plug (one blade is wider than the other) as a feature to reduce
the risk of electric shock. This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician.
Never use with an extension cord unless plug can be fully
inserted. Do not alter the plug.
This product complies with Part 18 of FCC Rules, but may
cause interference to radios, televisions, wireless telephones,
and remote controls. Avoid placing this product near these
devices. If interference occurs, move the product away from
the device or plug either into a different outlet. Do nozis
product near maritime safety equipment or other critical
navigation or communication equipment operating between
0.45-30 MHz.
This Class B RFLD complies with Canadian ICES-005
Diagram 1
Diagram 3
Diagram 2
Diagram 5
Diagram 4
Diagram 6
Diagram 7
A
A
F
I
M
E
G
B
D B
F
P
P
G
H
L
Q
K
C
C
B
O
O
N
N
A
J
Q
R
