LED Flex Lamp
A34G5B A34009 A3400C A34G5B-SHPR A34009-SHPR
ACDL10A
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
www.warranty.ottlite.com
NOTE: THIS UNIT IS FULLY ASSEMBLED
1.
Remove lamp from packing placing lamp body base (A) flat on
a steady surface.
2.
Connect the AC Adapter input (E) into connector (F) in the
rear-bottom of the lamp.
3.
Plug the A/C adapter (D) into a standard household 120V AC
outlet.
Note: Only use with the supplied AC adapter to
avoid damage or fire.
4.
Turn the lamp ON & OFF using power switch (B) located in the
front-upper side of base (A). Power switch (B) is a “touch” switch
that controls the dimmer function for 3 levels of brightness.
5.
To power LED settings, slightly touch the switch to achieve the
following:
» turn lamp “ON” to first lower-brightness; touch the
switch “once”;
» for medium-brightness; touch the switch “twice”;
» for high-brightness; touch the switch “three-times”;
» to turn lamp “OFF”; touch the switch “four-times”.
6.
To position the shade simply bend the flex-neck (G) as needed
to point the light. Please hold the lamp base (A) while adjusting
the lamp. Take care not to overextend the lamp to avoid
unbalancing it and damage. Please refer to diagrams for lamp
maximum adjustment range.
SAFETY WARNING:
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
1.
Turn lamp off and
WAIT UNTIL LAMP HEAD (C) and
ADAPTER (D) ARE COOL
before handling.
2.
The LED panel (L) might get hot after several hours of
continuous use,
DO NOT
place your hands directly on
LED light panel.
3.
Never use with an extension cord unless the plug can be fully
inserted into the receptacles in the extension cord.
4.
Do not alter the plug.
5.
The lamp head included with this unit cannot be replaced by
the consumer.
NOTE:
The important safety instructions appearing in this
instruction sheet are not meant to cover all possible conditions
and situations that may occur. It must be understood that
common sense, caution, and care must be used with any
electrical product.
CAUTION!
IF THE ExTERNaL FLExIbLE CabLE OR CORD OF
THIS LUmINaIRE IS DamagED, IT SHaLL bE ExCLUSIvELY REPLaCED bY
THE maNUFaCTURER OR ITS SERvICE agENT OR a SImILaR qUaLIFIED
PERSON IN ORDER TO avOID a HazaRD. INDOOR USE ONLY.
FCC Part 15
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
»
Reorient or relocate the receiving antenna.
»
Increase the separation between the equipment and receiver.
»
Connect the equipment into an outlet on a circuit different from
that of the receiver.
»
Consult the dealer or an experienced radio/TV technician
for help.
CAUTION:
Any change or modification to product not expressly
recognized by OttLite Technologies voids OttLite’s responsibility
for proper function of product.
This Class B digital apparatus complies with Canadian ICES-003
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.2A
Output: 20V DC, 250mA with a Male DC Plug
English
LED Flex Lamp
INS140107 REV041415
L
C
G
B
A
E
E
F
D
30°
30°
*Lamp cannot be used
in this position
120°
45°
45°
