CONGRATULATIONS!
You’ve purchased the finest in natural
lighting technology with your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to: OttLite.
com/warranty.
WARNING:
To prevent electric shock, make sure the lamp is
not plugged in until all assembly steps are complete.
CAUTION: TIP HAZARD.
DO NOT MOVE SHADE OR ACCESSORIES
outside of the
shaded area as shown in Figure 1. Shade and accessories
must be kept within the shaded area and must align in the
same forward-facing direction as the base.
LAMP ASSEMBLY
1.
Make sure the lamp is not plugged
into an electrical outlet.
2.
Remove wrench
(F)
, bolt
(E)
and washers
(D)
from the
plastic bag included in the box containing the base.
NOTE: On occasion, washers (D) may be ONE solid
washer that will serve the same purpose.
3.
With power cord aligned toward rear of base, firmly insert
the stem of the lamp into the hole located in the top of the
base.
4.
While holding stem into base of lamp, invert the lamp so
the base is in the air.
5.
Insert the bolt
(E)
through the lock washer
(D)
then
through the flat washer, and finally into the recessed hole
in the bottom of the base, as indicated in the diagram
(C)
.
6.
Using the enclosed wrench
(F)
, tighten the bolt
(E)
securely by turning clockwise.
7.
Plug lamp into a standard 120V socket. Your lamp is ready
for use.
8.
Turn lamp on or off by depressing rocker switch on
underside of shade.
TUBE INSERTION/REPLACEMENT
1.
Make sure that the lamp is not plugged into an electrical
socket.
2.
If the lamp has been in use, allow it to cool approximately 5
minutes before proceeding.
3.
To install a tube
(K)
in the socket, grasp the tube firmly in
your hand. Align tube pins with mating socket pin-holes,
clip the tube into the shade clip, then push it straight
into the socket until it “snaps” into place.
Do not apply
pressure to the glass end of the tube.
Pressure can
be applied to the tube base.
4.
To remove a tube
(K)
already installed in the lamp, grasp
the tube firmly in your hand, angle it slightly out of the
shade clip and then, using a slight side-to-side rocking
motion, pull it straight out of the socket.
Do not twist or
turn the tube.
BE CAREFUL TO AVOID TUBE BREAKAGE FROM HITTING
THE TUBE ON THE SHADE END.
5.
Plug the lamp into a standard 120V outlet.
6.
Turn lamp on or off by depressing switch
(J)
.
Please note that in operation, OttLite
®
tubes are not
dimmable.
Enjoy your OttLite
®
Craft Plus Floor Lamp!
This lighting system is designed for use with OttLite
®
type
(style number PL24-C). Use of other products
voids the warranty and may result in damage to the
lighting system.
CAUTION! IMPORTANT
SAFETY INSTRUCTIONS:
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE
BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL
FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE PLUG
DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE
PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED
ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD
UNLESS PLUG CAN BE FULLY INSERTED. DO NOT ALTER
THE PLUG.
If the external flexible cable or cord of this luminaire
is damaged, it shall be exclusively replaced by the
manufacturer or its service agent or a similar qualified
person in order to avoid a hazard. Indoor use only.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT, FULLY INSERT.
This product complies with Part 18 of FCC Rules, but
may cause interference to radios, televisions, wireless
telephones, and remote controls. Avoid placing this product
near these devices. If interference occurs, move the product
away from the device or plug either into a different outlet.
Do not install this product near maritime safety equipment
or other critical navigation or communication equipment
operating between 0.45-30 MHz.
ENGLISH
24w Classic Floor Lamp
INS140097 REV030714
24w Classic Floor Lamp
8FTPN4 GX7906
Usable area for shade
Area útil para la pantalla
Zone sécuritaire pour
l’abat-jour
DO NOT USE SHADE
IN THIS AREA
NO UTILICE LA
PANTALLA EN ESTA
AREA
NE PAS PLACER
L’ABAT-JOUR DANS
CETTE ZONE.
FIGURE 1 / FIGURA 1
