ENGLISH
ins 5 0003 rev 1101
CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
LAMP ASSEMBLY
1.
Unpack all lamp parts and lay out
on the floor with the base (A) lying
flat.
2.
Thread upper pole (D) to
adjustable arm end by hand, turning
clockwise until tight.
3.
Thread middle pole (C) to upper
pole (D) by hand, turning clockwise
until tight.
4.
Thread lower pole (B) to middle
pole (C) by hand, turning clockwise
until tight.
5.
Thread lower pole (B) to base (A)
by hand, turning clockwise until tight.
6.
Pull excess wire through bottom of
base.
7.
Attach harp (E) to socket arms (J)
by squeezing open ends of harp,
placing flattened section inside of arms
(J) and releasing. End by sliding collets
(K) over arms (J).
8.
Place shade (F) on harp (E).
9.
Place reflector (G) on top of shade
(F), making sure the white side faces
down.
10.
Thread finial (H) onto shade and
reflector by hand, turning clockwise
until tight.
11.
Install bulb following BULB
INSERTION/ REPLACEMENT
instructions.
12.
Plug the lamp into a standard
120V outlet.
13.
Turn lamp on or off by rotating the
switch (L) located on the socket
clockwise.
BULB INSERTION/REPLACEMENT
1.
Make sure the lamp is not plugged
into an electrical socket.
2.
If the lamp has been in use, allow it
to cool for approximately five minutes
before proceeding.
3.
To install a bulb in the socket, hold
the bulb (N) firmly near the base, align
bulb pins with matching pin-holes then
push it straight into the socket until it
"snaps" into place.
4.
To remove a bulb (N) already
installed in the lamp, grasp it firmly at
the base and, using a slight rocking
motion, pull it straight out of the
socket.
Do not twist or turn the
bulb.
Please note that in operation,
OTT-LITE
®
bulbs are not dimmable.
Enjoy your OTT-LITE
®
Collins Floor
Lamp!
This lighting system is designed for
use with OTT-LITE VisionSaver Plus
®
bulbs only (model number H3400K).
Use of other products voids the
warranty and may result in damage to
the lighting system.
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE
PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED
ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED. DO NOT ALTER
THE PLUG.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION:
BALLAST REQUIRES PROPER VENTILATION FOR PROPER OPERATION. A MINIMUM OF 6
INCHES OF AIR SPACE MUST BE PROVIDED ON ALL SIDES EXCEPT WHERE PLUGGED INTO AN ELECTRICAL OUTLET.
AVERTISSEMENT! IMPORTANTES DIRECTIVES DE
SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE
L'AUTRE). CE DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE
S'INSÈRE DANS LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE
N'ENTRE TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AVEC UNE RALLONGE SAUF
SI LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA FICHE
DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.
ATTENTION:
LES BALLASTS NÉCESSITENT UNE VENTILATION ADÉQUATE POUR UN FONCTIONNEMENT
CORRECT. UN MINIMUM DE 15 CM D'ESPACE DOIT ÊTRE LAISSÉ DE CHAQUE COTÉ À L'EXCEPTION DE CELUI OÙ
SE TROUVE LE BRANCHEMENT À LA PRISE D'ALIMENTATION ÉLECTRIQUE.
¡PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD
IMPORTANTES:
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES
MÁS ANCHA QUE LA OTRA) COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA.
ESTE ENCHUFE ENCAJARÁ EN CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE
NO CALZA COMPLETAMENTE EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN
CONTACTO CON UN ELECTRICISTA CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE
PUEDA SER TOTALMENTE INSERTADO. NO ALTERE EL ENCHUFE.
PRECAUCIÓN:
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA ANCHA DEL
ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
PRECAUCIÓN:
LA RESISTENCIA NECESITA UNA ADECUADA VENTILACIÓN PARA FUNCIONAR
CORRECTAMENTE. DEBE PROVEERSE UN ESPACIO DE AIRE DE UN MÍNIMO DE 6" EN TODOS LOS LADOS,
EXCEPTO DONDE ESTÁ CONECTADA A UN TOMACORRIENTE.
25W Collins Floor Lamp
25W
Collins Floor Lamp
25C92462
