manualshive.com logo in svg

otometrics AURICAL Aud, Reference Manual

Share
Download
otometrics AURICAL Aud Reference Manual Download Page 125

Stimulus presentation

Normal:

The signal is presented when the Stimulus Presentation button is activated.

Continuous ON:

The signal is interrupted when the Stimulus Presentation button is activated.

Pulse:

The signal is pulsed.

Pulse duration:

200 ms on and 200 ms off configurable

Bone oscillator

Bone oscillator output

The maximum speech output level from the bone oscillator depends on the actual sensitivity of the vibrator. The actual
maximum output is therefore determined at the time of calibration. The actual maximum output level may be determ-
ined by the operator by simply increasing the output level until the attenuator setting no longer increases.

Additionally, AURICAL Aud includes a feature which allows the operator to select the maximum output level from a bone
oscillator . Using this feature, the maximum output may be set lower than the physically available output level (installation
option).

As the maximum available output level will result in significant distortion from the bone oscillator , the specification below
limits the speech output level to 60 dBHL. Typical distortion levels (median values of a sample of bone oscillator ) are indic-
ated in the following table.

Total harmonic distortion (THD), %

Speech hearing level (dBHL) ->

60

50

40

30

Frequency below (Hz)

250

34,7

13,7

4,4

2,2

500

3,7

1

0,3

0,2

1000

2,6

0,9

0,3

0,3

Frequency response

Frequency

(Hz)

Nominal response level

(dB re. 1kHz level)

Tolerance

(dB)

250

-1.5

±4

500

6.5

±4

750

1.0

±4

1000

0.0

0

1

1500

1.5

±4

2000

-6.5

±4

Otometrics - AURICAL Aud

125

13 Technical specifications

Summary of Contents for AURICAL Aud









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands