COMMISSIONING
Before operation
Remove the protective cover of the battery in the remote control.
The remote control uses CR2025 batteries. For an interference-free
radio transmission, the RGB dimmer EasyOne should not be installed
in a metal case.
Connecting the input voltage
The RGB dimmer EasyOne works with an input voltage of 12V DC.
Note that the output voltage of the LED converter coincides with the
input voltage of the LED modules. The indicated loads of the converter
and the RGB dimmer EasyOne must not be exceeded.
Connecting the output voltage (LED modules)
The product supports LED modules operated with constant voltage.
Connect the plug and socket
Plug and socket are coded and can thus only be inserted to one
another in a determined position. Please align plug and socket
according to the coding and insert them into one another until a
significant mechanical stop is perceived. Check the correct fit of the
plug connection.
Connect the LED plug on the input voltage side of the RGB professi-
onal dimmer with a suitable power supply (i.e. Ostermann part no.
508.4000) and connect the LED socket on the output side to your
LED strips.
Programm a new remote control
At delivery status, the remote control and the dimmer are paired with
each other. A dimmer can work with up to three remote controls and
any remote control can be used with any number of receivers.
To learn a new remote control, proceed as follows:
1) Disconnect the RGB dimmer EasyOne for 5 seconds from the power
supply.
2) Hold down the buttons SPEED + and SPEED on the remote control
for 5 seconds.
The new remote control has been recognized and accepted. Atten-
tion! Only the three most recently programmed remote controls are
accepted by the RGB dimmer!
RGB Dimmer EasyOne
Part-no.: 508.4040
User manual
FEATURES
1) On / Off
Press the button (1) to switch the installation on/off. After turning
on the RGB dimmer EasyOne the dimmer returns to the value/pro-
gramm before switching off.
2) Programs
By pressing the buttons (2) and (9) you can switch between preset
programs.
3) Speed
With the keys (3) and (10) the speed of the programs is increased
(SPEED +) or decreased (SPEED).
4) Brightness
Use the keys (7) and (8) to increase () or decrease
(BRIGHT) the brightness of the installation.
6) Static colors
By pressing the buttons (6) you can switch between the default
colors.
7) Color short cuts
With these keys (4) / (5) you can select directly from 8 preset
colors.
8) Demo
Press DEMO (11) to switch to demonstration mode. Here 17 pro-
grams are played, one program is repeated three times.
5-24V D
C
+
RGB Steuerung
EasyOne
-
Max. Last: 3A
+
G
R
B
508.4040
LE
D
5-24V
DC
RGB Steuerung EasyOne
508.4040
LE
D G
R
B
INTENDED USE
The RGB dimmer EasyOne set is used to power and control LED
modules, i.e. LED strips (sold separately). Both the LED professional
remote control as well as the other components of this system are
designed exclusively for use in dry indoor locations. The LED professi-
onal remote control is used to control the RGB dimmer EasyOne by
radio signals. The RGB dimmer EasyOne may only be operated with
a suitable converter, which is approved for the operation of lamps
and works with a constant output voltage of 12V DC. In addition,
only LED modules may be connected, that can be operated with a
constanst voltage, which corresponds to the output voltage of the
LED converter.
Changes to the device or components can cause damage to it and in
addition can lead to potential risks such as short circuit, fire, electric
shock, etc. For injury or damage arising from improper use, not the
manufacturer but the operator is responsible.
Damage resulting from failure to observe the safety and installation
instructions will void all warranty claims. The manufacturer will not
be liable for any resulting consequential damage. Technical changes
that do not affect the contents of this installation and operating
instructions are reserved.
INTRODUCTION
Thank you for choosing a product from Rudolf Ostermann GmbH. We
want you to have a lot of fun with your new product and therefore ask
you to read these installation and operating instructions carefully. They
contain important information for installation and operation. Take care
if you pass the product on to third parties. Keep this document on file
for future reference.
SAFETY INSTRUCTIONS
• Make sure that no installation and connection wires are
damaged during installation!
• Do not use the device if it is damaged!
• Protect the device from moisture, water or heat!
• Do not operate the device in the immediate vicinity of flam-
mable gases, vapors and / or dust!
• Do not expose the product to heavy mechanical pressure!
• LED components are generally operated with so-called
protective low voltages (i.e. 12V or 24V). Do not connect any
components directly to 230V~, except when the respective
installation and operating instructions as well as the labeling
on the device does not explicitly specify this (for example,
primary side of power supplies). It can be fatal!
• Be sure to follow the safety instructions and documenta-
tion of any other appliances that are connected to these
devices!
• In commercial facilities, the safety regulations of the
professional trade association for electrical installations and
equipment must be observed.
• The product is not a toy! It contains small parts that can be
swallowed by children!
