Blade Oiling:
Carefully slide upper blade left or right far enough to place ONE
drop of oil on each running rail of the lower blade. Excess oiling
will cause hair to stick between teeth, slowing or jamming blades.
Turn on clipper and spray Oster
TM
Kool-Lube
lubricant through blade
teeth while clipper is running.
Blade Realignment:
After continued use, the clipper may
start to clatter or the blade sweep may
decrease. To adjust the clipper back to its
optimal performance, turn the calibration
screw in (clockwise) (Figure 2) until the
armature and field begin to make contact
(clatter). Back the screw out (counter
clockwise) approximately ¼ turn
(Figure 3).
STORAGE
Before replacing the blade guard for
clipper storage, spread one or two drops of oil over the blade to
prevent the blade from rusting. Replace the blade guard. Coil the
electric cord and secure with paper (not metal) twist fastener. Store
clipper in its original carton in a dry location.
Figure 2
Figure 3
1. Remove the plastic blade guard covering the teeth of the blades.
2. Disperse a few drops of clipper oil across the blades. Wipe off
excess oil with a clean, dry cloth.
NOTE:
Oil the blade frequently during use to help the blades stay
sharp longer.
DO NOT IMMERSE THE CLIPPER INTO ANY LUBRICANT.
3. Plug the clipper into electrical outlet.
4. Push the on-off switch to turn the clipper to “ON” position.
5. When finished clipping, turn the clipper off and unplug from the
electrical outlet.
6. Clean hair clippings from the blades using clipper or brush or an old
toothbrush. Wipe the housing with a clean, dry cloth.
Your complete kit includes the following:
Clipper
4 Comb Attachments:
Cleaning Brush
Clipper Oil
Blade Guard
* 07670-010: 1 set of additional blades included.
#
CUTS TO
1
1/8” (3mm)
2
1/4” (6mm)
3
3/8” (9mm)
4
1/2” (12mm)
Adjustable Blade Clipper
For Model Number:
076070-010
076070-310
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be
followed, including the following: Read all instructions before using the clipper.
SAVE THESE INSTRUCTIONS
OPERATING THE CLIPPER
DANGER
To reduce the risk of electric shock:
1. Do not reach for an appliance that has
fallen into water. Unplug immediately.
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it
can fall or be pulled into a tub or sink.
4. Do not place in or drop into water or
other liquid.
5. Always unplug this appliance from
electrical outlet immediately after using.
6. Unplug this appliance before cleaning,
putting on or taking off parts.
WARNING
To reduce the risk of burns, fire,
electric shock or injury to persons:
1. An appliance should never be left
unattended when it is plugged in.
2. Close supervision is necessary when
this appliance is used by, on, or near
children or invalids.
3. Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
4. Never operate this appliance if it has
a damaged cord or plug, if it is not
working properly, if it has been dropped
or damaged, or submerged into water.
5. Keep the cord away from heated
surfaces.
6. The intended continuous operating time
is 20 minutes.
7. Never drop or insert any object into any
opening.
8. Do not use outdoors or operate where
aerosol spray products are being used
or where oxygen is being administered.
9. Do not use this appliance with a
damaged or broken blade, as cut or
scratched skin may occur.
10. To disconnect, move all controls to
“OFF”, then remove plug from outlet.
11. During use, do not place or leave the
appliance where it is expected to be:
• subject to damage by animal, or
• exposed to weather.
12. Do not wrap cord around unit when
storing. Continuous stress on the cord
can damage cord insulation and result in
a shock hazard.
13. Avoid contact with moving blades.
14. Avoid tangling or kinking the cord while
clipping or trimming. Should the cord
become tangled or kinked, stop clipping
or trimming and straighten the cord.
15. This appliance is for clipping and
trimming purposes only.
16. Keep the appliance dry.
17. This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety. Children
should be supervised to ensure that they
do not play with the appliance.
ADJUSTMENTS FOR DIFFERENT CUTTING LENGTHS
Blade Adjustment:
Move thumb adjustment lever to raise or
lower bottom blade. Raise blade for fine
setting to cut hair very short for neck areas,
etc. lower blade for coarse setting to leave
hair longer for sideburns, etc. attachments
may also be used with adjustable clippers.
Follow regular attachments instructions
(Figure 1).
ATTACHING GUIDE COMBS:
To Attach:
Get front edge of blade started in comb track. Press palm
of hand against blade guard and push comb onto blade. If there is
resistance, place drop of oil on inner side of comb. If blade guard is
not available, use precaution when pressing hand against comb.
BLADE MAINTENANCE
To maintain longer clipper blade life, we recommend periodic cleaning
and oiling, using Oster
TM
Blade Wash cleaning solution (catalog
no. 76300-103) and 5 weight oil Blade Lube lubricant (Catalog No.
76300-106). We also recommend the use of Oster Kool-Lube lubricant
(Catalog No. 76300- 101) during extended usage.
Blade Cleaning:
Position the blade in a flat dish filled with just enough Blade Wash
to cover only the blade. Turn on clipper and listen for change in
the hum of the motor. As the build-up is removed, the clean blade
runs faster and higher pitch. When the pitch stabilizes (30 to 60
seconds), turn off clipper and unplug. Use a lint-free cloth to wipe
blade as dry as possible. Oil blades.
Fine
Coarse
Screw Holes
Bottom Blade
Screw
Plate
Top Blade
Screw
Holes
Figure 1
SERVICE INFORMATION
How and Where to Get Service
INFORMATION • DO NOT DESTROY • READ CAREFULLY
The foundation of our business has been built upon the principle of
service to the user, both in designing superior products and in keeping
them in condition to give long-lasting use. That is why we back up our
reputation for manufacturing top-quality products by providing the finest
service facilities possible for adjustment and repairs, when necessary.
Please retain the original packaging materials and carton, if possible, to
facilitate the packaging of the product if service is required. Contact the
phone number listed on the last page for warranty service.
Printed in China. P.N. 9100990000444
076070-010/-310-061_-800_15EIM1 GCDS-OST40826-JC
-E2-
-E3-
-E4-
-E5-
© 2015 Sunbeam Products, Inc. doing business as Jarden Consumer
Solutions. All rights reserved. Distributed by Jarden Consumer
Solutions (Asia) Limited, 40/F Manhattan Place, 23 Wang Tai Road,
Kowloon Bay, Hong Kong. One Year Limited Warranty – contact
phone number listed on the last page for details. Sunbeam Products,
Inc. and Jarden Consumer Solutions (Asia) Limited are subsidiaries of
Jarden Corporation (NYSE: JAH).
076070-010-061_-800_15EIM1.indd 1
11/3/15 09:41
