Osram ams TSL2521 Manual Download Page 24

 

 

Document Feedback 

TSL2521 ALS/Flicker 

 

 

Legal Information 

 

 

Application Note 

• PUBLIC 

 

AN001042 

• v1-01 • 2022-Jan-27 

23

 

│ 23 

 

Legal Information 

Copyrights & Disclaimer 

Copyright ams-OSRAM AG, Tobelbader Strasse 30, 8141 Premstaetten, Austria-Europe. Trademarks Registered. All rights 
reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written 
consent of the copyright owner.  

Information in this document is believed to be accurate and reliable. However, ams-OSRAM AG does not give any 
representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no 
liability for the consequences of use of such information. 

Applications that are described herein are for illustrative purposes only. ams-OSRAM AG makes no representation or warranty 
that such applications will be appropriate for the specified use without further testing or modification. ams-OSRAM AG takes no 
responsibility for the design, operation and testing of the applications and end-products as well as assistance with the 
applications or end-product designs when using ams-OSRAM AG products. ams-OSRAM AG is not liable for the suitability and 
fit of ams-OSRAM AG products in applications and end-products planned.  

ams-OSRAM AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, 
property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, 
of any kind, in connection with or arising out of the furnishing, performance or use of the technical data or applications described 
herein. No obligation or liability to recipient or any third party shall arise or flow out of ams-OSRAM AG rendering of technical or 
other services. 

ams-OSRAM AG reserves the right to change information in this document at any time and without notice. 

 

RoHS Compliant & ams Green Statement 

RoHS Compliant:

 The term RoHS compliant means that ams-OSRAM AG products fully comply with current RoHS directives. 

Our semiconductor products do not contain any chemicals for all 6 substance categories plus additional 4 substance categories 
(per amendment EU 2015/863), including the requirement that lead not exceed 0.1% by weight in homogeneous materials. 
Where designed to be soldered at high temperatures, RoHS compliant products are suitable for use in specified lead-free 
processes.  

ams Green (RoHS compliant and no Sb/Br/Cl):

 ams Green defines that in addition to RoHS compliance, our products are free 

of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) 
and do not contain Chlorine (Cl not exceed 0.1% by weight in homogeneous material). 

Important Information:

 The information provided in this statement represents ams-OSRAM AG knowledge and belief as of the 

date that it is provided. ams-OSRAM AG bases its knowledge and belief on information provided by third parties, and makes no 
representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third 
parties. ams-OSRAM AG has taken and continues to take reasonable steps to provide representative and accurate information 
but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ams-OSRAM AG 
and ams-OSRAM AG suppliers consider certain information to be proprietary, and thus CAS numbers and other limited 
information may not be available for release. 

 

Headquarters 

ams-OSRAM AG 

Tobelbader Strasse 30 

8141 Premstaetten 

Austria, Europe 

Tel: +43 (0) 3136 500 0 

Please visit our website at 

www.ams.com

 

Buy our products or get free samples online at 

www.ams.com/Products

 

Technical Support is available at 

www.ams.com/Technical-Support

 

Provide feedback about this document at 

www.ams.com/Document-Feedback

 

For sales offices, distributors and representatives go to 

www.ams.com/Contact

 

For further information and requests, e-mail us at 

[email protected]

 

 

 

Summary of Contents for ams TSL2521

























Reviews: