Oshkosh JLG 1500SJ, Service And Maintenance Manual

Page: 376 / 706

SECTION 5 - BASIC HYDRAULIC INFORMATION & HYDRAULIC SCHEMATICS
5-22 – JLG Lift – 3121262
Table 5-13. O-ring Boss (ORB) - Table 2 of 6
TYPE/FITTING IDENTIFICATION
STUD ENDS
with (ORFS) or S series DIN (MBTS) opposite end
MATERIAL Dash Size
Thread Size ØA* Torque
(UNF) (in) (mm) Min Nom Max Min Nom Max
ST
EE
L F
IT
TINGS
WIT
H
ST
EE
L MA
TING
CO
M
P
ON
EN
TS; UN
-L
UB
RIC
AT
ED
TH
RE
ADS
2 5/16-24 0.31 7.93 -- -- -- -- -- --
3 3/8-24 0.37 9.52 -- -- -- -- -- --
4 7/16-20 0.44 11.11 26 27 28 35 37 38
5 1/2-20 0.50 12.70 30 32 33 40 43 45
6 9/16-18 0.56 14.28 35 37 39 46 50 53
8 3/4-16 0.75 19.10 60 63 66 80 85 89
10 7/8-14 0.87 22.22 100 105 110 135 142 149
12 1 1/16-12 1.06 27.00 135 142 149 185 193 202
14 1 3/16-12 1.19 30.10 175 184 193 235 249 262
16 1 5/16-12 1.31 33.30 200 210 220 270 285 298
20 1 5/8-12 1.63 41.30 250 263 275 340 357 373
24 1 7/8-12 1.87 47.60 305 321 336 415 435 456
32 2 1/2-12 2.50 63.50 375 394 413 510 534 560
TYPE/FITTING IDENTIFICATION
STUD ENDS
with (ORFS) or S series DIN (MBTS) opposite end
MATERIAL Dash Size
Thread Size ØA* Torque
(UNF) (in) (mm) Min Nom Max Min Nom Max
AL
UMINUM/B
RASS FIT
TINGS OR AL
UMINUM/B
RASS
MA
TIN
G
C
O
MPON
ENTS
; UN-
LUBRIC
ATED TH
READS
2 5/16-24 0.31 7.93 -- -- -- -- -- --
3 3/8-24 0.37 9.52 -- -- -- -- -- --
4 7/16-20 0.44 11.11 17 18 18 23 24 24
5 1/2-20 0.50 12.70 20 21 21 27 28 28
6 9/16-18 0.56 14.28 23 24 24 31 33 33
8 3/4-16 0.75 19.10 39 41 43 53 56 58
10 7/8-14 0.87 22.22 65 69 72 88 94 98
12 1 1/16-12 1.06 27.00 88 93 97 119 126 132
14 1 3/16-12 1.19 30.10 114 120 126 155 163 171
16 1 5/16-12 1.31 33.30 130 137 143 176 186 194
20 1 5/8-12 1.63 41.30 163 171 179 221 232 243
24 1 7/8-12 1.87 47.60 198 208 218 268 282 296
32 2 1/2-12 2.50 63.50 244 256 268 331 347 363
* ØA Thread OD dimension for reference only.
**Removal Torque for Zero Leak Gold® Hollow Hex Plugs is significantly higher than install torque, typically 1.5-3.5X install torque.