manualshive.com logo in svg

OSF 310.000.0580, Installation And Operating Instructions Manual, Page: 1 / 44

Share
Download
OSF 310.000.0580 Installation And Operating Instructions Manual Download Page 1

Installation and Operating Instructions 

 

Filter control unit with built-in level control 

 

and LAN port 

Part no. 

310.000.0580

 

 

Technical data 

Dimensions: 

300mm x 285mm x 85mm 

Operating voltage: 

3/N/PE 400V/230V 50Hz 

Power consumption of control unit: 

 

approx.5VA 

(depends on operating mode) 

Switching 

Pump: 

max. 8A / 3.0 kW (AC3) 

capacity: 

Heater: 

max. 3A / 0.4 kW (AC3) 

 

Dosing system: 

max. 3A / 0.4 kW (AC3) 

 

Auxiliary output: 

max. 3A / 0.4 kW (AC3) 

Degree of protection: 

IP 40 

Level sensors: 

12V Safety Extra Low Voltage (SELV) 

Ambient temperature: 

0-40°C 

Air humidity: 

0-95% non-condensing 

Memory card: 

Micro SD 

Internet port: 

LAN 

Compatible pumps 

230V single-phase pump 
(rated current up to 8A) 

400V three-phase pump 
(rated current up to 8A) 

Speck ECO-Touch-Pro pump 

Speck Badu-90-ECO-VS pump 

Speck Badu-90-ECO-Motion pump 

Pentair IntelliFlo pump 

Pentair SuperFlo pump 

Zodiac FloPro VS pump 

UWE PMM pump 

Summary of Contents for 310.000.0580













































Reviews:

No comments