Doc. ID 10109204
OPERATOR MANUAL
OSD2051
10/100Base-Tx to 100Base-Fx
MEDIA CONVERTER
The OSD2051 is designed to convert between
10/100Base-Tx copper cabling and 100Base-Fx fiber via
the SFP port. Operation over at least 40km of singlemode
fiber is possible by use of the appropriate optical devices.
The unit operates over one or two fibers depending on the
SFP used. It is equipped with one SFP port, one RJ45
and power jack. For ease of network monitoring and fault
isolation the OSD2051 has 4 indicators (see tables).
Specifications and Features
▲
Complies with the IEEE 802.3 standard.
▲
Supports network traffic of 10 or 100Mbps.
▲
Automatic TP setup: no need for crossover
cables
▲
Auto-sensing of half or full duplex operation.
▲
Automatic set up for 10 or 100Mbps on copper
side.
▲
A very compact design that fits in the camera
housing
▲
Available for singlemode, multimode operation
over a variety of link budgets
▲
Available for operation over 1 or 2 fibers
▲
Powered by non-critical 12VDC or 24VAC
supplies
▲
Operates over –20 to +75
°
C temperature range
▲
Utilizes 10/100Base-Fx SFP transceivers that
can be selected according to specific length or
fiber requirements without changing the whole
unit
Fitting SFP Connectors
Care should be taken when inserting/removing the SFP
connectors as SFP modules are Electrostatic (ES) sensitive and
Electrostatic Discharge (ESD) precautions should be taken
when installing. Ensure that the SFP is fully engaged and
latched into position.
Inserting SFP
– Ensure that the SFP lever is in the locked
position and insert into SFP port. Gently push the SFP until it
locks into place. Remove dust cap and fit fiber cable.
Removing SFP
– Remove fiber connector. Pull the SFP lever
down to unlock SFP from housing. Using the lever, gently pull
the SFP out.
Case Dimensions and Mounting Details
Below is an outer case drawing showing the dimensions.
The OSD2051 can be mounted on the optional mounting base
clips by simply utilizing the OSD2051 ribbed edge. Dimensions
below
Power Connection
The voltage range of the OSD2051 is 8V
DC
to 35V
DC
or 22 to
28V
AC
@ 3VA. Connect power to the connector located at the
front of the case (see diagram).
Signal Connection
Ethernet cable should be connected to the RJ45 Copper
connector on the OSD2051. The appropriate SFP
connector should be inserted into the SFP port.
The optical fiber cable must be terminated with the
appropriate type optical connector (SC for single fiber and
LC for 2 fiber). Before connection, inspect the ends of the
connectors to ensure that no dust or dirt is present as it
could contaminate the modem connector and result in poor
performance.
If it is necessary to clean the cable connectors use
isopropyl alcohol and lint free tissue to remove
contamination.
SFP Port Options
OSD Part
Number
SFP Description
SFP10/100LFx
2 fiber SFP plug-in transceiver @
1310nm
SFP10/100WLFxA
1 fiber SFP plug-in transceiver (Tx
@ 1310nm, Rx @ 1550nm)
SFP10/100WLFxB
1 fiber SFP plug-in transceiver (Tx
@ 1550nm, Rx @ 1310nm)
Inserting
SFP
Removing
SFP
1
2
55
26
52
Ethernet cable
LC Fiber cable
Power
51.3
49.3
8.6
21.3
Ø3.2
51.3
+V
0V
