Oryx solutions SCA 1200ht User Manual Download Page 26

     

 

26 

 

 

 

Supplemental Information 

 

SCA 1200ht Support Cleaning Apparatus Limited Warranty 

Product 

Limited Warranty Period 

SCA 1200ht Support Cleaning Apparatus 

1 year 

All  new  Support  Cleaning  Apparatus  (SCA)  systems  are  warranted  exclusively  by 
Oryx Additive

, Inc.’s (“Manufacturer”) limited warranty as follows: 

Each  Support  Cleaning  Apparatus  system  (“System”)  and  its  components 
(“Components”), except those listed below under limits and exclusions, is warranted 
against  defects  in  the materials  and  workmanship  for  a  period  of  one (1)  year from 
the date of installation at the end user

’s (“Customer”) facility. 

Repair  or  replacement  only:  manufacturer's  liability  under  this  agreement  shall  be 
limited  to  repairing  or  replacing,  at  the  discretion  of  manufacturer,  parts,  or 
components sufficient to return the system to conform to the marketing specifications 
of the system.  

Components subject to wear during normal use and over time such as paint, finish, 
light bulbs, seals, etc., are excluded from this warranty. 

This  warranty  is  void  if  the  system  is  subjected  to  mishandling,  misuse,  neglect, 
accident,  improper  installation,  improper  maintenance,  or  improper  operation  or 
application,  or  if  the machine  was  improperly  repaired  or  serviced  by the  customer.  
This  warranty  is  void  if  the  system  is  not  installed  by  a  certified  distributor  and  the 
proper  installation  documentation  provided  by  the  manufacturer  has  not  been 
submitted. 

Liability, whether based on warranty, negligence or other cause, arising out of and/or 
incidental to sale, use or operation of the system, or any part thereof, shall not in any 
case exceed the cost of repair or replacement of the defective equipment, and such 
repair or replacement shall be the exclusive remedy of the purchaser, and in no case 
will  manufacturer  be  responsible  for  any  and/or  all  consequential  or  incidental 
damages including without limitation, and/or all consequential damages arising out of 
commercial losses. 

This  warranty  is  transferrable  from  the  original  end  user  to  another  party  if  the 
machine is sold via private sale before the end of the warranty period. 

The  foregoing  is  a  limited  warranty  and  it  is  the  only  warranty  by  manufacturer. 
MANUFACTURER  DISCLAIMS  ALL  OTHER  WARRANTIES,  EXPRESS  OR 
IMPLIED,  INCLUDING  BUT  NOT  LIMITED  TO  ALL  WARRANTIES  OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 

Summary of Contents for SCA 1200ht



























Reviews: