manualshive.com logo in svg

Orthman 125-087-02-EN-OM, Operator'S Manual, Page: 46 / 62

Share
Download
Orthman 125-087-02-EN-OM Operator'S Manual Download Page 46

TROUBLESHOOTING

DR12x2 Row Hopper Planter OM-EN 

6-2

Preventative Measures

CAUTION

!

Avoid implement and hydraulic system damage. Always 
perform the following preventative measures to prevent 
damage:

  • Lubricate all load bearing points.
  • All hardware should be checked for tightness before 

operation.

  • Be sure all hydraulic hoses are securely connected 

and all fittings are tight.

  • Be sure all hydraulic hoses are secured in a manner 

that keeps them away from sharp edges and moving 
objects that can rupture a hose. 

  • Be sure the case drain hose connected to all 

hydraulic motors of the machine (such as the 
vacuum fans) is connected to the case drain port of 
the tractor. 

  • The case drain allows hydraulic oil to flow out of the 

motor casing and back into the tractor sump when 
hydraulic fluid is no longer being sent to the motor. If 
this fluid is not able to escape the motor casing, 
damage may occur to the internal components of the 
hydraulic motor when motor is stopped suddenly and 
not allowed to slow down gradually. As a good 
practice, the tractor selective control valve (SCV) 
controlling the hydraulic motor should always be 
placed in "float" when the hydraulic motor is intended 
to be stopped. 

  • Be sure the tractor hydraulic system has the proper 

amount of hydraulic fluid. 

Troubleshooting

DANGER

!

Avoid crushing. Failure to follow this information will 
result in death or serious injury. Make sure all personnel 
are clear of the implement before lowering. 

Lower the implement to the ground, place the tractor in 
park, turn off the engine, and remove the key.

DANGER

!

Avoid crushing. Failure to follow this information will 
result in death or serious injury. Use bar stands and 
cylinder stops to support the implement. 

Store the implement on a clean, dry, level surface. An 
uneven surface could cause the implement to shift or 
fall, resulting in injury or death as well as implement 
damage. Securely support all implement components 
that must be raised. Store the implement away from 
human activity.

  • Remove buildup of grease, oil, and debris before you 

adjust the implement.

DANGER

!

High-pressure fluid can penetrate eyes and skin. 
Relieve pressure on hydraulic system before servicing 
or disconnecting hoses. Wear proper hand and eye 
protection. When searching for leaks, use cardboard or 
wood instead of hands.

Summary of Contents for 125-087-02-EN-OM































































Reviews:

No comments