manualshive.com logo in svg

Orthman 125-087-02-EN-OM, Operator'S Manual, Page: 30 / 62

Share
Download
Orthman 125-087-02-EN-OM Operator'S Manual Download Page 30

PREPARATION AND SETUP

DR12x2 Row Hopper Planter OM-EN 

4-6

Disconnecting Implement From 

Tractor

See the tractor operator’s manual for more information 
on properly disconnecting the implement.

1. Park implement on a clean, level surface; strong 

enough to support the weight of the machine.

2. Unfold the toolbar. See “Wing Fold” on page 4-7.
3. Install the float link lock pins (1) into the rigid positions 

(2) to lock the wings in place. Adjust the hydraulic 
cylinders to align pin holes in the wing fold link plates.

ORM000128

Figure 4-5:  Right Wing

DANGER

!

Avoid crushing. Failure to follow this information will 
result in death or serious injury. Use bar stands and 
cylinder stops to support the implement.

4. Lower the bar stands (3) and install stay pins (4).

ORM000129

Figure 4-6:  Right Wing

DANGER

!

Avoid crushing. Failure to follow this information will 
result in death or serious injury. Make sure all personnel 
are clear of the implement before lowering.

5. Lower the implement onto the bar stands by placing 

the tractor three-point hitch into the “float” position.

DANGER

!

Avoid crushing. Failure to follow this information will 
result in death or serious injury. Do not stand between 
the tractor and implement when connecting or 
disconnecting the implement.

6. Place the tractor in park, turn off the engine, and 

remove the key before disconnecting the implement. 

DANGER

!

Avoid high-pressure fluid hazards. Failure to follow this 
information will result in death or serious injury. Relieve 
hydraulic pressure before servicing or disconnecting 
hoses.

7. Relieve hydraulic system pressure before 

disconnecting the tractor. Disconnect hydraulic 
hoses from tractor selective control valve (SCV).

8. Disconnect all machine electrical connections from 

tractor. 

9. Disconnect tractor three-point hitch points from the 

implement hitch pin and tug pins. If tractor quick-hitch 
is used, lower the quick-hitch until the hooks are 
below the implement hitch pin and tug pins and the 
machine is safely on the ground.

1) Float link lock pin 

(2 used)

2) Rigid position (2 used)

2

1

3) Bar stand (2 used)

4) Stay pin (2 used)

4

3

Summary of Contents for 125-087-02-EN-OM































































Reviews:

No comments