manualshive.com logo in svg

Orthman 125-087-02-EN-OM, Operator'S Manual, Page: 17 / 62

Share
Download
Orthman 125-087-02-EN-OM Operator'S Manual Download Page 17

SAFETY INFORMATION

DR12x2 Row Hopper Planter OM-EN 

2-9

Prepare for Emergencies

Be prepared for a fire. Keep a readily accessible fire 
extinguisher at all times.

Keep a readily accessible stocked first aid kit and 
emergency phone numbers for your doctor, hospital, 
ambulance, and fire department.

Wear protective clothing and equipment. Wear clothing 
appropriate for the situation. Protect your eyes, ears, 
hands, and feet with the use of protective goggles, ear 
plugs, gloves, boots, etc.

Anhydrous Ammonia (NH3) and 

Liquid Fertilizer

DANGER

!

Avoid direct exposure to anhydrous ammonia (NH3) 
and liquid fertilizer. Failure to follow this information will 
result in death or serious injury. 

Use extreme care when working with anhydrous 
ammonia (NH3) and liquid fertilizer.

Keep a clean supply of water readily accessible in case 
of exposure to NH3 or liquid fertilizer.

Wear protective goggles and gloves when working with 
NH3 or liquid fertilizer. Be sure all persons involved in the 
operation are properly trained concerning the dangers 
and precautions involved in the application of NH3 or 
liquid fertilizer.

If you choose to apply NH3 or liquid fertilizer, it is 
advisable to consult documented information regarding 
safe handling and application of NH3 or liquid fertilizer. 
Information is available from the following recognized 
sources:

• American National Standards Institute (ANSI): 

www.ansi.org - (212) 642-4900

• Material Safety Data Sheets (MSDS): 

www.msdsonline.com

• National Safety Council: www.nsc.org/necas

• The Fertilizer Institute: www.tfi.org

• United States Department of Transportation 

(USDOT): www.dot.gov

• Compressed Gas Association: www.cganet.com

Safety Never Hurts

CAUTION

!

Read and understand the entire contents of this manual 
before operating or servicing the implement.

Use the following safety practices:

  • Understand all implement functions.
  • Never stand between the tractor and implement 

when connecting or disconnecting the implement.

  • Be aware of all surroundings before you move the 

implement.

  • Operate the implement from operator’s seat only.
  • Never mount or dismount a moving tractor.
  • Never leave the engine running when the implement 

is unattended.

  • Keep away from power driven parts when in motion.
  • Make sure all personnel are clear before lowering 

implement to the ground.

Orthman Serial Number Plate

The Orthman serial number plate contains valuable 
information. The model number (1) and serial number (2) 
provide Orthman dealers and the Orthman service 
department with the exact specifications of your 
implement if any warranty or service issues need to be 
addressed.

ORM000117

Figure 2-3

1) Model number

2) Serial number

RTHMAN MFG., INC.

L E X I N G T O N ,   N E B R A S K A

MODEL

3 0 8 - 3 2 4 - 4 6 5 4

O

SERIAL

#

#

1

2

Summary of Contents for 125-087-02-EN-OM































































Reviews:

No comments