Orthman 125-082-01-EN-OM Operator'S Manual Download Page 21 | Manualshive

Page: 21 / 86

Orthman 125-082-01-EN-OM Operator'S Manual Download Page 21

SAFETY INFORMATION

1TRIPR II Row Units OM-EN

2-11

Orthman Left Side Decals

NOTE:

Orthman double bar toolbar is shown. Orthman

rigid toolbar is similar.

ORM000296

Figure 2-6

C A U T I O N

1. Read and understand all operator manuals before implement use.
2. Follow all tractor or towing device operating procedures and safety guidelines.
3. Do not allow riders on implement.
4. Lower implement to the ground, place tractor in park, turn off engine, and remove key.
Wait for all moving parts to come to a complete stop before working on implement.
5. Be extremely careful working around unshielded sharp edges.
6. Make sure all safety lighting and decals are clean. Use hazard lights when in transport.
7. Engage all safety devices before transporting or working beneath implement.
8. Contact or close proximity to power lines can result in electrocution.
9. Review all safety instructions with all operators on a frequent basis.

«
...
19
20
21
22
23
...
»

Summary of Contents for 125-082-01-EN-OM























































































Reviews:

No comments