background image

Warranty

LIMITED TWO YEAR CONSUMER WARRANTY:

Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be

defective in workmanship or material under normal use, for a period of two years from the date of

purchase from the dealer as indicated by the date code marking of the product 

PROVIDED 

the product

was installed by an authorized Directed dealer. During this two-year period, there will be no charge for this

replacement 

PROVIDED

the unit is returned to Directed, shipping pre-paid.  If the unit is installed by

anyone other than an authorized Directed dealer, the warranty period will be one year from the date of

purchase by the dealer as indicated by the date code marking of the product. This warranty is non-

transferable and does not apply to any unit that has been modified or used in a manner contrary to its

intended purpose, and does not cover damage to the unit caused by installation or removal of the unit.

During this one-year period, there will be no charge for this replacement 

PROVIDED

the unit is returned

to Directed, shipping pre-paid. This warranty is void if the product has been damaged by accident or

unreasonable use, neglect, improper service or other causes not arising out of defects in materials or

construction.  Units which are found to be damaged by abuse resulting in thermally damaged voice coils

are not covered by this warranty but may be replaced at the absolute/sole discretion of Directed. 

ALL

WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,

WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WARRANTY OF NON-

INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM

EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO

ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT.  DIRECTED HAS

ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS

AUTHORIZED DEALERS OR INSTALLERS.

Unit must be returned to Directed, postage pre-paid, with bill

of sale or other dated proof of purchase bearing the following information: consumer's name, telephone

number, and address, authorized dealer's name and address, and product description.  Note: This warranty

does not cover labor costs for the removal and reinstallation of the unit.   

IN ORDER FOR THIS

WARRANTY TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF INSTALLATION BY AN

AUTHORIZED DIRECTED DEALER.  ALL UNITS RECEIVED BY DIRECTED FOR WARRANTY REPAIR

WITHOUT PROOF OF DIRECTED DEALER INSTALLATION WILL BE COVERED BY THE LIMITED 1 YEAR

PARTS AND LABOR WARRANTY.

Note: This warranty does not cover labor costs for the removal and

reinstallation of the unit. 

BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS

THAT ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN

ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.

© 2004 Directed Electronics, Inc.  All rights reserved.  G46010  12-04

22--c

ch

ha

an

nn

ne

ell  a

am

mp

plliiffiie

err

22--c

ch

ha

an

nn

ne

ell  a

am

mp

plliiffiie

err

Summary of Contents for ORION WCC 1600.2






















Reviews: