ORiNG TRGPS-9084GT-M12X-BP2-MV User Manual Download Page 9

Page: 9 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

ardware Overview

2.1 Front Panel

The device provides the following ports on the front panel. All connectors are in M12 type to

ensure tight, robust connections, as well as reliable operation against environmental

disturbances, such as vibration and shock.

Port

Description

Power

connector

1 x power connector with 4-pin M12 male S-coding connector

Ethernet ports

8 x 10/100/1000Base-T(X) P.S.E coppoer ports with 8-pin M12 female

X-coding connector

4 x 10/100/1000Base-T(X) non-PoE ports with bypass function with

8-pin M12 female X-coding connector

Console

1 x console port with 5-pin M12 female A-coding connector

Relay output

1 x relay output with 5-pin M12 female A-coding connector

Reset button

1 x reset button

2.2 Front Panel LED

LED

Color

Status

Description

PWR

Green

DC power module activated

R.M

Green

Device operating in Ring Master mode

Ring

Green

Ring enabled

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV



















































































































































































Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands

ORiNG TRGPS-9084GT-M12X-BP2-MV, User Manual

Search results

Summary of Contents for TRGPS-9084GT-M12X-BP2-MV

Reviews:

Brands by name

Popular brands