Quick Installation Guide
Version 2.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
ORing's Transporter
series managed Ethernet switches are designed for
T M
industrial applications, such as rolling stock, vehicle, and railway
applications.
is managed Redundant Ring Ethernet
TGS-9200-M12-BP2
switch with 20x10/100/1000Base-T(X) ports which is specifically designed for
the toughest and fully compliant with EN50155 requirement.
The switch
support Ethernet Redundancy protocol, O-Ring (recovery time < 30ms over
250 units of connection), O-Chain, MRP
MSTP/RSTP/STP (IEEE
*NOTE
802.1s/w/D) can protect your mission-critical applications from network
interruptions or temporary malfunctions with its fast recovery technology.
TGS-9200-M12-BP2
includes 2 sets of bypass ports that protect the network
from failures and Network maintenance by ensuring network integrity during
power loss. And support wide operating temperature from -40 C to 75 C.
o
o
TGS-9200-M12-BP2
can also be managed centralized and convenient by
Open-Vision, Except the Web-based interface, Telnet and console (CLI)
configuration. Therefore, the switch is one of the most reliable choices for
EN50155 highly-managed Ethernet application.
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1:
Hold the
evice upright against the wall
d
Step 2:
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screws to the wall with a screwdriver.
Step 3:
Slide the
evice downwards and tighten the four screws for added stability.
d
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow:
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading:
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TGS-9200-M12-BP2
Pictures
Number
1
CD
1
Panel Layouts
Front View
1. Reset button
2. Power1 status LED
3. Power2 status LED
4. R.M. status LED
5. Ring status LED
6. Fault LED
7. Power connector
8. Gigabit Ethernet ports
(G1 - G4 are bypass ports)
9. Link/ACT LED for Gigabit ports
10. Speed LED for Gigabit ports
11. Relay output
12. Console port
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for dual power inputs.
Step 1:
Insert a power cable to the power connector on the device.
Step 2:
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay
N.C.
3A@24VDC
Network Connection
The switch has twenty 10/100/1000Base-T(X) Ethernet ports in the form of M12 connector.
Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network
devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
TGS-9200-M12-BP2
TGS-9200-M12-BP2
1907-200-Q9200M1222-FX010
S w i tc h
E N 5 0 1 5 5
EN50155 20-port managed
Gigabit Ethernet switch
I N D U S T R I A L
1
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
8-pin female M12
A-coding connector
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
8-pin female M12
A-coding connector
1000BASE-T
Cat. 5/Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
8-pin female M12
A-coding connector
For pin assignments of the Ethernet ports, please refer to the following tables.
QIG
1
11
12
7
4
5
6
7
8
2
1
3
4 5 6
2 3
8
10
9
8-Pin Gigabit Port Definition
PIN
Definition
1
BI_DC+
2
BI_DD+
3
BI_DD-
4
BI_DA-
5
BI_DB+
6
BI_DA+
7
BI_DC-
8
BI_DB-
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an close circuit when an event is triggered.
Console port pinouts
N.C.
RXD
RS-232, 115200bps, 8, N, 1
GND
TXD
N.C.
Dimension
V1+
V1-
V2+
V2-
4
5
6
7
8
2
1
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
3
G1~G20
Power
Failure
Bypass
Power
Failure
Bypass
Power
Failure
Bypass
15
19.4
91.3
180
260
Unit =mm (Tolerance ±0.5mm)
216
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
G17
G18
G19
G20
G13
G14
G15
G16
Fault
Ring
R.M.
PWR2
PWR1
Reset
3A@24VDC
Relay
N.C.
Relay Output
Console
RSVD
RXD
RS-232, 115200bps, 8, N, 1
GND
TXD
N.C.
Power
G1
LNK/ACT
Speed
G2
LNK/ACT
Speed
G3
LNK/ACT
Speed
G4
LNK/ACT
Speed
G9
G10
G11
P12
G5
G6
G7
G8
TGS-9200-M12-BP2
193.9
7.5
188.4
Ø5.0
Ø8.0
*NOTE : This function is available by request only
V1+
V1-
V2+
V2-
4
5
6
7
8
2
1
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
3
G1~G20
Power
Failure
Bypass
Power
Failure
Bypass
Power
Failure
Bypass
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
G17
G18
G19
G20
G13
G14
G15
G16
Fault
Ring
R.M.
PWR2
PWR1
Reset
3A@24VDC
Relay
N.C.
Relay Output
Console
RSVD
RXD
RS-232, 115200bps, 8, N, 1
GND
TXD
N.C.
Power
G1
LNK/ACT
Speed
G2
LNK/ACT
Speed
G3
LNK/ACT
Speed
G4
LNK/ACT
Speed
G9
G10
G11
P12
G5
G6
G7
G8
TGS-9200-M12-BP2
