Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
The
unmanaged Ethernet switche is designed for industrial
applications, such as rolling stock, vehicle, and railway applications. The
switch boasts EN50155 compliance and M12 connectors to ensure tight
and robust connections, and guarantee reliable operation against
environmental disturbances, such as vibration and shock. With eight
10/100Base-T(X) ports, the switch provides a wide operating temperature
range from -40 C to 70 C.
TES-180-M12
o
o
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Hold the
evice upright against the wall
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Slide the
evice downwards and tighten the four screws for added stability.
Step 1:
Step 2:
Step 3:
d
d
The device is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
Contents
TES-180-M12
Pictures
Number
1
QIG
1
Dimension
Panel Layouts
Front View
1. Ethernet port
2. Power port
3. LNK/ACT LED for LAN ports
4. Duplex/Collision LED for LAN ports
5. Power status LED
Wiring
Power port pinouts
The device supports power supply in M12 5-pin female connector on
the front panel for the dual power inputs.
Insert a power cable to the power connector on the device.
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Step 1:
Step 2:
Network Connection
The switch has eight 10/100Base-T(X) Ethernet ports in the form of M12 connector. Depending on
the link type, the switch uses CAT 3, 4, 5, 5e UTP cables to connect to network devices (PCs,
servers, switches, routers, or hubs). Please refer to the following table for cable specifications.
TES-180-M12
TES-180-M12
1907-2-29-TES180M12-1.0
Switch
EN50155
EN50155 8-port unmanaged
Ethernet switch
I N D U S T R I A L
1
2
3
4
5
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the switch
between the wall and the screws.
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
4-pin female M12
D-coding connector
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
4-pin female M12
D-coding connector
M12/4P Pin Definition
For pin assignments of the LAN ports, please refer to the following tables.
Tx+
Rx+
Tx-
Rx-
Configurations
After installing the switch and connecting cables, start the
evice by turning on
power. The green power LED should turn on. Please refer to the following tablet
for LED indication.
d
178.2
R2.5
R4.00
40.0
15.0
7.50
150.0
44.4
73.9
138.0
88.9
FDX
12-48 VDC
V-
V+
Tx+
Rx+
Tx-
Rx-
N.C.
N.C.
N.C.
P1
P2
P3
P4
P5
P6
P7
P8
PWR
FDX
FDX
FDX
TES-180-M12
FDX
12-48 VDC
V-
V+
Tx+
Rx+
Tx-
Rx-
N.C.
N.C.
N.C.
P1
P2
P3
P4
P5
P6
P7
P8
PWR
FDX
FDX
FDX
TES-180-M12
V-
V+
N.C.
N.C.
N.C.
Pin No.
Description
#1
RD+
#2
TD+
#3
RD-
#4
TD-
LED
Color
Status
Description
PWR
Green
On
DC power module is activated
10/100Base-T(X)
On
Port is Linked
LNK/ACT
Green
Blinking
Transmitting data
On
Port is in duplex mode
Duplex /
Collision
Amber
Blinking
Collision occurs
